AMT Datasouth Accel-7450 User Manual Download Page 8 | Manualshive

Page: 8 / 45

background image

ACCEL- 7450

-

8

-

•

Turn the ribbon feed knob counterclockwise to remove any slack in
the ribbon.

Connecting the printer to the power source

•

Make sure that the power switch is set to off. Connect the printer with the

supplied power cord to an AC outlet.

Connect the AC power plug to an AC outlet of the voltage designated on the
rating label located on the back of the printer.

Ribbon Feed Knob

«
...
6
7
8
9
10
...
»

Summary of Contents for Accel-7450














































Reviews:

No comments

Related manuals for Accel-7450

Brand: m3d Pages: 23

Brand: m3d Pages: 26

SCX-4300 - SCX 4300 B/W Laser

Brand: Samsung Pages: 97

SCX 4828FN - Laser Multi-Function Printer

Brand: Samsung Pages: 151

SCX 4725FN - B/W Laser - All-in-One

Brand: Samsung Pages: 120

SCX 4500 - B/W Laser - All-in-One

Brand: Samsung Pages: 97

SCX 4200 - B/W Laser - All-in-One

Brand: Samsung Pages: 95

SCX 4500 - B/W Laser - All-in-One

Brand: Samsung Pages: 172

ProXpress M337x

Brand: Samsung Pages: 56

PROXPRESS M332 SERIES

Brand: Samsung Pages: 50

ML-2240 - 23 Ppm Mono Laser Printer

Brand: Samsung Pages: 82

Brand: Samsung Pages: 8

ML-1610 - B/W Laser Printer

Brand: Samsung Pages: 134

ML-1610 - B/W Laser Printer

Brand: Samsung Pages: 112

Brand: Samsung Pages: 128

Brand: Samsung Pages: 152

ML 3471ND - B/W Laser Printer

Brand: Samsung Pages: 207

ML 2150 - B/W Laser Printer

Brand: Samsung Pages: 237

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands