AMT Datasouth 7200 User Manual Download Page 70

Page: 70 / 72

7200 APPENDIX

APPENDIX-5

Operation Manual

A.1.7 Inserter

(1) Document feeding direction
(2) Shutter
(3) Non-standard documents inserted

(4) Document feeding

(5) Documents rejected

A.1.8 Output Stacker

(1) Capacity
(2) Document direction
(3) Full detection

A.1.9 Transfer Ribbon Printing (Type D printers only)

(1) Near-end detection

(2) End detection
(3) Breakage detection
(4) Standardization

(5) Life span

(6) Setting
(7) Multi-time print

Face side up, leading side first in

Not available

Passed back to the front inserter to be kept,

or jammed in the carrier structure

The beep sound occurs when a document is
fed normally

Passed to the output stacker

100 documents

Face side up, leading side first out
Available

Available; approximately 10 documents

before end

Available
Not available

Refer to the transfer ribbon specifications

5,000 documents per roll (maximum, while

multi-time printing)

Thermal transfer (TT)
Four stages available, set on the front

control panel

Summary of Contents for 7200









































































Search results

Summary of Contents for 7200

Reviews:

Brands by name

Popular brands

AMT Datasouth 7200, User Manual

Search results

Summary of Contents for 7200

Reviews:

Brands by name

Popular brands