AMT Datasouth 7200 User Manual Download Page 61

Page: 61 / 72

7200

4-12

Operation Manual

4.2 Error Messages

When an error has occurred in the ATB printer, an error message is displayed on the LCD
panel. The error messages are listed in the table below.

Error Message

Error State

Recovery Procedure

WARNING:

Indicates a relatively minor error, ex.
when consumption articles (documents,

etc.) has run short (paper-out), when the
operator has made a mistake, etc.

Open the cover, take necessary actions for

recovery, and close the cover.
If the error continues, contact a service
technician.

PAPER JAM:

Indicates an error caused by the paper

jam. The block where the paper jam has

occurred is displayed.

Open the cover, remove the jammed
coupon, and close the cover.

COM.ERROR:

Indicates an error in communication with
the terminal.

Verify communication parameters. If the

error continues, contact a service

technician.

ENCODING
ERROR:

Indicates an error during magstripe

encoding.

The error coupon is automatically ejected

and voided.

Press the RESET key.
If the error continues, contact a service
technician.

MAGNETIC
ERROR:

Indicates an error during magstripe

decoding.

Press the RESET key.
If the error continues, contact a service
technician.

SYSTEM ERROR:

Indicates an error that seldom occurs
under ordinary circumstances.

Power the printer off and on. If the error

continues, contact a service technician.

OTHERS:

Indicates other errors such as AEA
programming errors, etc.Indicates a
relatively minor error. For example, end

of expendables (coupons) or operator
errors.

Power the printer off and on. If the error

continues, contact a service technician.

Summary of Contents for 7200









































































Search results

Summary of Contents for 7200

Reviews:

Brands by name

Popular brands

AMT Datasouth 7200, User Manual

Search results

Summary of Contents for 7200

Reviews:

Brands by name

Popular brands