manualshive.com logo in svg

Amsco STERIS, Manual

Share
Download
Amsco STERIS Manual Download Page 38

5 — Routine Maintenance

28
11830378_C

AMSCO

®

Rack Return

Operator Manual

Never try to open both doors at the same time.

Never try to open a door manually.

Never interfere with automatic accessory rack movement.

WARNING
PERSONAL INJURY

Never try to intentionally close the door when the safety lock is not properly retracted

during routine maintenance.

Clean equipment with a general purpose cleaner to remove general stains, a stainless-steel stain remover for stubborn

stains, and a stainless-steel polish to keep equipment looking new.

1. Press Command button to open door and put safety lock in place.

NOTE: Safety lock is located on the upper left corner of the door opening.

1

Safety Lock

Figure 5-1. Safety Lock

2. Turn rack return power OFF.

If SCS Conveyor System is present, turn SCS Conveyor System power OFF.

3. Look for any debris or instruments that could have been dropped and left in the chamber. If so, remove it.

Summary of Contents for STERIS

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands