manualshive.com logo in svg

AMS AMS-CZYG008-NG, Manual, Page: 2 / 18

Share
Download
AMS AMS-CZYG008-NG Manual Download Page 2

2/

18

Important Safety Information

3

Natural Gas Warnings

5

Parts List

7

Pre-use Instructions

11

Lighting Instructions

12

Care and Cleaning

13

Gas Component Connection Checks

14

Troubleshooting

16

Warranty

18

Table of Contents

The instruction manual contains important information necessary for the proper

assembly and safe use of the appliance.

Read and follow all warnings and instructions before assembling and using the

appliance.

Follow all warnings and instructions when using the appliance.

If instructions or parts are missing, 

please contact Xiamen Charm garden or local distributors.

DANGER

CARBON MONOXIDE HAZARD

This appliance can produce carbon

monoxide

which has no odor.

Using it in an enclosed space can kill you.

Never use this appliance in an enclosed space 

such as a camper,tent,car or home.

WARNING : If the information in this manual is not followed exactly,

a fire or explosion may result causing property damage,personal injury,

or loss of life.

Summary of Contents for AMS-CZYG008-NG



















Reviews:

No comments