Ampt 31570013 Installation Manual Download Page 19

Page: 19 / 22

Chapter 2: Installing the Ampt-CU

2014

AMPT,

LLC.

Figure

10:

Network

Settings

Home

Screen

Follow the onscreen directions for each task.

Restoring

Factory

Defaults

The network settings and password can be restored to factory default values by pressing and
holding the

Restore

button during the boot process. If you are using this feature to restore the

password, be sure to record your network settings first. See

Configuring the Ampt-CU

Network Settings

on page 18 for more details.

To restore the network settings and password:

Press the

Restart

button

The LEDs will be on continuously for several seconds.

When the

Com

LED flashes, press and hold the

Restore

button until the

Com

and

Fault

LEDs alternate flashing.

The network settings and password are restored and the unit automatically reboots.

Summary of Contents for 31570013






















Search results

Summary of Contents for 31570013

Reviews:

Related manuals for 31570013

Brands by name

Popular brands

Ampt 31570013, Installation Manual

Search results

Summary of Contents for 31570013

Reviews:

Related manuals for 31570013

Brands by name

Popular brands