background image

Details of all products and services provided by Ampetronic can be found 

at www.ampetronic.com
Wall mount brackets are available for mounting the amplifier on the wall 

with appropriate fixings.
Microphone pre-amplifiers for 1, 2 or 5 microphones, as well as other line 

level signals. These can be powered from either the ±15V DC power 

socket on the rear of the unit, or a stand alone power supply.
Signal processing units are available for use with low spill array systems.
Input adaptors for a range of applications such as 100V line audio & low Z 

speaker systems are available.

This product carries a five year parts and labour warranty from date of 

shipment from Ampetronic. To qualify for the five year warranty, the 

product must be registered at www.ampetronic.com (products/warranty), 

without which the warranty will be valid for two years only.

The five year warranty is dated from the time the equipment leaves 

Ampetronic and NOT when it is installed.

Manufacturer: 

Ampetronic Ltd.

Northern Road,

Newark,

Nottinghamshire.

NG24 2ET

United Kingdom.

Declares that the product:

Description:

Induction Loop Driver

Type name:

ILD500

Conforms to the following Directive(s) and Norm(s):

Directive 2004/108/EC

EMC:

EN55103-1 : 2009 Emission

EN55103-2 : 2009 Immunity

 

Directive 2006/95/EC

Safety:

EN60065 : 2002

Date: January 2011

J.R. Pieters

Managing Director

Ampetronic Ltd.

WARRANTY

 

DECLARATION OF CONFORMITY

UP15401-5

ACCESSORIES

Summary of Contents for ILD500













Reviews: