AMP AMP TDBU REMOTE, Programming Manual

Page: 6 / 14

A M P
™
T D B U R E M O T E |
P R O G R A M M I N G G U I D E
6
AMP
™
TDBU Remote Function
1. Channel Options
Select A Channel
a. Press “<” button on the remote to select a lower channel.
b. Press “>” button on the remote to select a higher
channel.
Hide Unused Channels
a. Press and Hold (about 3 sec)
“<” and “>”
buttons simul-
taneously until remote control displays “C” (channel).
b. Press “<” or “>” button to select required quantity of
channel (between 1 to 15).
c. Press
“Stop”
button to confirm selection (the example
shows a 5-channel selection). The LCD will display “
O
” (OK)
once to confirm selection.
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Remote Response
Remote Response
Remote Response
a.
a.
b.
b.
c.
+ or
Higher
Channel
Higher
Channel
Higher
Channel
Lower
Channel
Lower
Channel
Lower
Channel
Higher
Channel
Higher
Channel
Higher
Channel
Stop
2. Advanced Setting - Disable Limit Setting
AMP25B
Instruction
Attention
-1-
The motor is suitable for motorization of roller blinds, sheer shadings, roman shades, and zebra shades.
Never drop, knock, drill or submerge the motor. Keep the power cable in right position as following.
Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
Declarations
d electrical products appropriately.
-2-
Safety
1. Do not expose motor to humid, damp or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna and keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If power cable or connector is damaged, do not use.
6. Ensure correct crown and drive adaptor are used.
7. Ensure power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls shall be properly isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered
operation.
11. Installation and programming to be performed by a qualified professional, use or modification outside
the scope of this instruction may void warranty.
Features
Fields of Application
Specifications
Following data for reference
Working temperature: -10 ℃ ~ +50 ℃
Input Voltage: USB 5V 1A / USB 5V 2A
Radio Frequency: 433.925MHz
Maximum Running Time: 6 minutes
Model
Rated Torque
(N.m)
Rated Speed
(rpm)
Rated Power
(W)
AMP25B - 0.7/34 0.7 34 8
AMP25B -1.1/28 1.1 28 8
Charging Instructions
This motor has a built in Li-ion battery pack with integrated charge management.
Max power input for recharging: 5V 2A.
Before first use please charge motor for 6 hours. Using 5V charger (most phones charger is 5V ) .
During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and
needs to be charged.
During operation, the voltage was detected to be too low, the battery was about to run out, the battery stopped
running and needed to be recharged.
Rechargeable Battery
Blinking red:
Low battery alert
Blinking green:
Charging is processing
Solid green:
Battery has
finished charging.
FCC Text - text 01
Add A zoom in on the
charging port
P1 Button Instructions
P1 button
Lithium Battery Switch
LED light
Micro-USB Port
Add visual explanation of P1 - file 02
Sheer Roller Revolve
Roman shades
Advanced Setting - Disable Limit Setting
a. Remove the cover from the backside of remote,
the lock switch is in the right corner.
b. Move the switch to the “Lock” position to disable
the following commands, remote will show “L” (lock):
- Change Motor Direction
- Setting the Upper and Lower Limit
- Adjust Limit
- Roller Mode or Sheer Mode
c. Move the switch to
“Unlock”
position to assess all
remote functions, remote will show
“U”
(unlock).
a.
b.
c.
Switch
Switch
Switch
Lock
Lock
Unlock
Unlock
*This advanced feature is intended to be used after
all shade programming is completed. User Mode will
prevent accidental or unintended changing of limits.
L
U
a. Remove the cover from the backside of remote, the lock
switch is in the right corner.
b. Move the switch to the “Lock” position to disable the
following commands, remote will show “L” (lock):
- Change Motor Direction
- Setting the Upper and Lower Limit
- Adjust Limit
- Roller Mode or Sheer Mode
c. Move the switch to “Unlock” position to assess all remote
functions, remote will show “U” (unlock).
a.
b.
c.
Switch
Switch
Lock Unlock
Switch
Lock Unlock
*This advanced feature is intended to be used after all
shade programming is completed. User Mode will prevent
accidental or unintended changing of limits.
!
Essential Settings
The steps in factory mode must be completed to ensure proper operation.
* All setup needs to
be done using
LEFT
SIDE
of the remote
.
8. Adjust Motor Speed
Channel Options 6. Roller Mode and Sheer Mode
7. Add or Remove Additional Remote
5. Favorite Position
2. Change Motor Direction (if necessary)
3. Setting the Upper and Lower Limits
4. Adjust Limits
1. Pair / Unpair Remote Control
Jog x1
Jog x1
Jog x2
a. Press “P1” button (about 2 sec) on the
End Cap as shown until motor jog x1.
b. In the next 10 secs, press and hold Left
“Stop”
button on the remote control until
motor jog x2.
4.1 Adjust the Upper Limit
a. Press and hold (about 5 sec) Left “Up”
and
Left “Stop”
buttons simultaneously
until motor jog x1.
b. Press Right “Up” button to raise the
Middle Rail, then press
Right “Stop”
button when it is in the new desired
upper limit.
c. Press
Left “Up”
button to raise the
Bottom Rail, then press Left “Stop”
button when it is in the new desired
upper limit.
d. Press and hold (about 5 sec) Left
“Up” and Left “Stop” buttons
simultaneously until motor jog x2.
6.1 Roller Shade Mode - continue
movement after a short press -
Default Mode
a. Press and hold (about 5 sec)
Left “Up”
and Left “Down” buttons simultaneously
until motor jog x1.
b. Press and hold (about 2 sec) Left
“Stop”
button until motor jog x2.
7.1 Using Current Remote Control
a. On the current remote control, press
and hold (about 2 sec) one
“P2”
button
until motor jog x1.
b. Once more, on the current remote
control, press and hold (about 2 sec) one
“P2” button until motor jog x1.
c. On the New remote control, press and
hold (about 2 sec) one “P2” button until
motor jog x2.
8.1 Acceleration Speed
a. Press one “P2” button until motor
jog x1.
b. Press
Left “Up”
button until motor
jog x1.
c. Once more, press Left “Up” button
until motor jog x2.
Select A Channel
a. Press “<” button on the remote to
select a lower channel.
b. Press
“>”
button on the remote to
select a higher channel.
6.2 Sheer Shade Mode - jog
movement after a short press
(continue movement after a long
press)
a. Press and hold (about 5 sec)
Left “Up”
and Left “Down” buttons simultaneously
until motor jog x1.
b. Press and hold (about 2 sec) Left
“Stop”
button until motor jog x1.
8.2 Decelaration Speed
a. Press one
“P2”
button until motor
jog x1.
b. Press Left “Down” button until motor
jog x1.
c. Once more, press Left “Down” button
until motor jog x2.
Hide Unused Channels
a. Press and Hold (about 3 sec) “<” and
“>” buttons simultaneously until remote
control displays “C” (channel).
b. Press
“<” or “>”
button to select
required quantity of channel (between
1 to 15).
c. Press “Stop” button to confirm
selection (the example shows a 5-channel
selection). The LED will display “O” (OK)
once to confirm selection.
5.1 Set Favorite Position
a. Use Left “Up” or Left “Down” button
to move the shade to desired Favorite
position.
b. Press and hold (about 2 sec) one “P2”
button on the back of remote control until
motor jog x1.
c. Press and hold (about 2 sec) Left
“Stop” button until motor jog x1.
d. Once more, press and hold (about 2
sec) Left “Stop” button until motor jog x2.
5.3 Delete Favorite Position
a. Press and hold (about 2 sec) one “P2”
button until motor jog.
b. Press and hold (about 2 sec)
Left
“Stop” button until motor jog.
c. Once more, press and hold (about
2 sec)
Left “Stop”
button until motor
jog x1.
4.2 Adjust the Lower Limit
a. Press and hold (about 5 sec) Left
“Down” and Left “Stop”
buttons
simultaneously until motor jog x1.
b. Use Left “Down” button to lower
the Bottom Rail then press
Left “Stop”
button when it is in the new desired
lower limit.
c. Press
Right “Down”
button to lower
the Middle Rail, then press
Right “Stop”
button when it is in the new desired
lower limit.
d. Press and hold (about 5 sec)
Left
“Down” and Left “Stop buttons
simultaneously until motor jog x2.
5.2 Send Shade to Favorite Position
Press and hold (about 2 sec) Left “Stop”
button, motor will move to Favorite
position.
Press
Left “Up”
or
Left “Down”
button
to check if the shade moves in the desired
direction.
If you need to reverse the direction, press
and hold (about 2 sec) Left “Up” and
“Down” buttons simultaneously until
motor jog x1.
3.1 Set Upper Limit
a. Press Right “Up” button to raise the
Middle Rail, then press
Right “Stop”
button when it is in the desired upper limit.
b. Press Left “Up” button to raise the
Bottom Rail, then press Left “Stop”
button when it is in the desired upper limit.
c. Press and hold (about 5 sec) Left “Up”
and Left “Stop” buttons simultaneously
until motor jog x2.
*The operation is only valid when there are no limits.
* Repeat the same procedure to unpair
remote control.
*If you exit the limit setting status before
you finish the limit settings, the motor will
take the previous existing limits.
*If the motor has no response, it already
has a Maximum or Minimum speed.
3.2 Set Lower Limit
a. Press Left “Down” button to lower the
Bottom Rail, then press Left “Stop”
button when it is in the desired lower limit.
b. Press Right “Down” button to lower
the Middle Rail, then press
Right “Stop”
button when it is in the desired lower limit.
c. Press and hold (about 5 sec)
Left
“Down”
and
Left “Stop”
buttons
simultaneously until motor jog x2.
Action on
Motor
Action on
Remote Control
+
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
Motor Response
Middle Rail
Response
Motor Response
Bottom Rail
Response
Left Up Left Down
Left Stop
a.
a.
a.
a.
a.
a.
a.
b.
b.
b.
b.
b.
a.
a.
a.
c.
b.
b.
b.
c.
b.
c.
c.
c.
c.
b.
d.
Jog x2
+
Left Up
Right Up Left Up
Left Stop
a.
a.
b.
b.
Action on
Remote Control
Action on
Remote Control Action on
Remote Control
Motor Response
Bottom Rail
Response Middle Rail
Response
Jog x1
+
Left Down Left Stop
Left Down
Jog x1
Jog x2
+
Left Up Left Down
Left Stop
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
Jog x1
Jog x1
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
+
+
or
Left Up
Lower
Channel
Lower
Channel
Left Down
Higher
Channel
Higher
Channel
Left Stop
Jog x1
Jog x2
Jog x1
Current Remote Control
New Remote Control
Current Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
P2
P2
P2
Jog x1
Jog x1 Jog x1
Jog x2
Jog x1
Jog x2
Left Up
Higher
Channel
Lower
Channel
Left Up
Left Down
Left Down
Stop
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Remote
Response
Motor Response
Motor Response
Remote
Response
Remote
Response
Motor Response
Remote
Response
P2
P2
C
11
O 5
1 15
7.2 New Remote Control
Follow instructions under the section 1.
Pair / Unpair Remote Control
*Repeat the same procedure to remove
additional remote control.
c.
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Bottom Rail
Response
Motor Response
Middle Rail
Response
Jog x2
+
Left Down
Left Down Right Down
Left Stop
a.
b.
c.
P1
d.
Action on
Remote Control
Motor Response
Jog x2
+
Left Down Left Stop
c.
Right Down
a.
b.
Action on
Remote Control
Action on
Remote Control Action on
Remote Control
Motor Response
Middle Rail
Response Bottom Rail
Response
Jog x1
+
Left Up Left Stop
Right Up
d.
Action on
Remote Control
Motor Response
Jog x2
+
Left Up Left Stop
c.
Left Up
Jog x1
Jog x1 Jog x2
Jog x1
Jog x1
Jog x1
or
or
or
Left Up Left Down
Left Stop
Left Stop
Left Stop
Left Stop
Left Stop
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Shade Response
Motor Response
Motor Response
Motor Response
P2
P2
!
Essential Settings
The steps in factory mode must be completed to ensure proper operation.
* All setup needs to
be done using
LEFT
SIDE
of the remote
.
8. Adjust Motor Speed
Channel Options 6. Roller Mode and Sheer Mode
7. Add or Remove Additional Remote
5. Favorite Position
2. Change Motor Direction (if necessary)
3. Setting the Upper and Lower Limits
4. Adjust Limits
1. Pair / Unpair Remote Control
Jog x1
Jog x1
Jog x2
a. Press “P1” button (about 2 sec) on the
End Cap as shown until motor jog x1.
b. In the next 10 secs, press and hold Left
“Stop”
button on the remote control until
motor jog x2.
4.1 Adjust the Upper Limit
a. Press and hold (about 5 sec) Left “Up”
and
Left “Stop”
buttons simultaneously
until motor jog x1.
b. Press Right “Up” button to raise the
Middle Rail, then press
Right “Stop”
button when it is in the new desired
upper limit.
c. Press
Left “Up”
button to raise the
Bottom Rail, then press Left “Stop”
button when it is in the new desired
upper limit.
d. Press and hold (about 5 sec) Left
“Up” and Left “Stop” buttons
simultaneously until motor jog x2.
6.1 Roller Shade Mode - continue
movement after a short press -
Default Mode
a. Press and hold (about 5 sec)
Left “Up”
and Left “Down” buttons simultaneously
until motor jog x1.
b. Press and hold (about 2 sec) Left
“Stop”
button until motor jog x2.
7.1 Using Current Remote Control
a. On the current remote control, press
and hold (about 2 sec) one
“P2”
button
until motor jog x1.
b. Once more, on the current remote
control, press and hold (about 2 sec) one
“P2” button until motor jog x1.
c. On the New remote control, press and
hold (about 2 sec) one “P2” button until
motor jog x2.
8.1 Acceleration Speed
a. Press one “P2” button until motor
jog x1.
b. Press
Left “Up”
button until motor
jog x1.
c. Once more, press Left “Up” button
until motor jog x2.
Select A Channel
a. Press “<” button on the remote to
select a lower channel.
b. Press
“>”
button on the remote to
select a higher channel.
6.2 Sheer Shade Mode - jog
movement after a short press
(continue movement after a long
press)
a. Press and hold (about 5 sec)
Left “Up”
and Left “Down” buttons simultaneously
until motor jog x1.
b. Press and hold (about 2 sec) Left
“Stop”
button until motor jog x1.
8.2 Decelaration Speed
a. Press one
“P2”
button until motor
jog x1.
b. Press Left “Down” button until motor
jog x1.
c. Once more, press Left “Down” button
until motor jog x2.
Hide Unused Channels
a. Press and Hold (about 3 sec) “<” and
“>” buttons simultaneously until remote
control displays “C” (channel).
b. Press
“<” or “>”
button to select
required quantity of channel (between
1 to 15).
c. Press “Stop” button to confirm
selection (the example shows a 5-channel
selection). The LED will display “O” (OK)
once to confirm selection.
5.1 Set Favorite Position
a. Use Left “Up” or Left “Down” button
to move the shade to desired Favorite
position.
b. Press and hold (about 2 sec) one “P2”
button on the back of remote control until
motor jog x1.
c. Press and hold (about 2 sec) Left
“Stop” button until motor jog x1.
d. Once more, press and hold (about 2
sec) Left “Stop” button until motor jog x2.
5.3 Delete Favorite Position
a. Press and hold (about 2 sec) one “P2”
button until motor jog.
b. Press and hold (about 2 sec)
Left
“Stop” button until motor jog.
c. Once more, press and hold (about
2 sec)
Left “Stop”
button until motor
jog x1.
4.2 Adjust the Lower Limit
a. Press and hold (about 5 sec) Left
“Down” and Left “Stop”
buttons
simultaneously until motor jog x1.
b. Use Left “Down” button to lower
the Bottom Rail then press
Left “Stop”
button when it is in the new desired
lower limit.
c. Press
Right “Down”
button to lower
the Middle Rail, then press
Right “Stop”
button when it is in the new desired
lower limit.
d. Press and hold (about 5 sec)
Left
“Down” and Left “Stop buttons
simultaneously until motor jog x2.
5.2 Send Shade to Favorite Position
Press and hold (about 2 sec) Left “Stop”
button, motor will move to Favorite
position.
Press
Left “Up”
or
Left “Down”
button
to check if the shade moves in the desired
direction.
If you need to reverse the direction, press
and hold (about 2 sec) Left “Up” and
“Down” buttons simultaneously until
motor jog x1.
3.1 Set Upper Limit
a. Press Right “Up” button to raise the
Middle Rail, then press
Right “Stop”
button when it is in the desired upper limit.
b. Press Left “Up” button to raise the
Bottom Rail, then press Left “Stop”
button when it is in the desired upper limit.
c. Press and hold (about 5 sec) Left “Up”
and Left “Stop” buttons simultaneously
until motor jog x2.
*The operation is only valid when there are no limits.
* Repeat the same procedure to unpair
remote control.
*If you exit the limit setting status before
you finish the limit settings, the motor will
take the previous existing limits.
*If the motor has no response, it already
has a Maximum or Minimum speed.
3.2 Set Lower Limit
a. Press Left “Down” button to lower the
Bottom Rail, then press Left “Stop”
button when it is in the desired lower limit.
b. Press Right “Down” button to lower
the Middle Rail, then press
Right “Stop”
button when it is in the desired lower limit.
c. Press and hold (about 5 sec)
Left
“Down”
and
Left “Stop”
buttons
simultaneously until motor jog x2.
Action on
Motor
Action on
Remote Control
+
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
Motor Response
Middle Rail
Response
Motor Response
Bottom Rail
Response
Left Up Left Down
Left Stop
a.
a.
a.
a.
a.
a.
a.
b.
b.
b.
b.
b.
a.
a.
a.
c.
b.
b.
b.
c.
b.
c.
c.
c.
c.
b.
d.
Jog x2
+
Left Up
Right Up Left Up
Left Stop
a.
a.
b.
b.
Action on
Remote Control
Action on
Remote Control Action on
Remote Control
Motor Response
Bottom Rail
Response Middle Rail
Response
Jog x1
+
Left Down Left Stop
Left Down
Jog x1
Jog x2
+
Left Up Left Down
Left Stop
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
Jog x1
Jog x1
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
+
+
or
Left Up
Lower
Channel
Lower
Channel
Left Down
Higher
Channel
Higher
Channel
Left Stop
Jog x1
Jog x2
Jog x1
Current Remote Control
New Remote Control
Current Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
P2
P2
P2
Jog x1
Jog x1 Jog x1
Jog x2
Jog x1
Jog x2
Left Up
Higher
Channel
Lower
Channel
Left Up
Left Down
Left Down
Stop
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Remote
Response
Motor Response
Motor Response
Remote
Response
Remote
Response
Motor Response
Remote
Response
P2
P2
C
11
O 5
1 15
7.2 New Remote Control
Follow instructions under the section 1.
Pair / Unpair Remote Control
*Repeat the same procedure to remove
additional remote control.
c.
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Bottom Rail
Response
Motor Response
Middle Rail
Response
Jog x2
+
Left Down
Left Down Right Down
Left Stop
a.
b.
c.
P1
d.
Action on
Remote Control
Motor Response
Jog x2
+
Left Down Left Stop
c.
Right Down
a.
b.
Action on
Remote Control
Action on
Remote Control Action on
Remote Control
Motor Response
Middle Rail
Response Bottom Rail
Response
Jog x1
+
Left Up Left Stop
Right Up
d.
Action on
Remote Control
Motor Response
Jog x2
+
Left Up Left Stop
c.
Left Up
Jog x1
Jog x1 Jog x2
Jog x1
Jog x1
Jog x1
or
or
or
Left Up Left Down
Left Stop
Left Stop
Left Stop
Left Stop
Left Stop
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Shade Response
Motor Response
Motor Response
Motor Response
P2
P2
!
Essential Settings
The steps in factory mode must be completed to ensure proper operation.
* All setup needs to
be done using
LEFT
SIDE
of the remote
.
8. Adjust Motor Speed
Channel Options 6. Roller Mode and Sheer Mode
7. Add or Remove Additional Remote
5. Favorite Position
2. Change Motor Direction (if necessary)
3. Setting the Upper and Lower Limits
4. Adjust Limits
1. Pair / Unpair Remote Control
Jog x1
Jog x1
Jog x2
a. Press “P1” button (about 2 sec) on the
End Cap as shown until motor jog x1.
b. In the next 10 secs, press and hold
Left
“Stop” button on the remote control until
motor jog x2.
4.1 Adjust the Upper Limit
a. Press and hold (about 5 sec)
Left “Up”
and
Left “Stop”
buttons simultaneously
until motor jog x1.
b. Press
Right “Up”
button to raise the
Middle Rail, then press
Right “Stop”
button when it is in the new desired
upper limit.
c. Press
Left “Up”
button to raise the
Bottom Rail, then press Left “Stop”
button when it is in the new desired
upper limit.
d. Press and hold (about 5 sec) Left
“Up” and Left “Stop” buttons
simultaneously until motor jog x2.
6.1 Roller Shade Mode - continue
movement after a short press -
Default Mode
a. Press and hold (about 5 sec)
Left “Up”
and Left “Down” buttons simultaneously
until motor jog x1.
b. Press and hold (about 2 sec)
Left
“Stop”
button until motor jog x2.
7.1 Using Current Remote Control
a. On the current remote control, press
and hold (about 2 sec) one
“P2”
button
until motor jog x1.
b. Once more, on the current remote
control, press and hold (about 2 sec) one
“P2”
button until motor jog x1.
c. On the New remote control, press and
hold (about 2 sec) one “P2” button until
motor jog x2.
8.1 Acceleration Speed
a. Press one “P2” button until motor
jog x1.
b. Press
Left “Up”
button until motor
jog x1.
c. Once more, press Left “Up” button
until motor jog x2.
Select A Channel
a. Press “<” button on the remote to
select a lower channel.
b. Press
“>”
button on the remote to
select a higher channel.
6.2 Sheer Shade Mode - jog
movement after a short press
(continue movement after a long
press)
a. Press and hold (about 5 sec) Left “Up”
and Left “Down” buttons simultaneously
until motor jog x1.
b. Press and hold (about 2 sec)
Left
“Stop”
button until motor jog x1.
8.2 Decelaration Speed
a. Press one
“P2”
button until motor
jog x1.
b. Press Left “Down” button until motor
jog x1.
c. Once more, press Left “Down” button
until motor jog x2.
Hide Unused Channels
a. Press and Hold (about 3 sec) “<” and
“>” buttons simultaneously until remote
control displays “C” (channel).
b. Press
“<” or “>”
button to select
required quantity of channel (between
1 to 15).
c. Press “Stop” button to confirm
selection (the example shows a 5-channel
selection). The LED will display “O” (OK)
once to confirm selection.
5.1 Set Favorite Position
a. Use Left “Up” or Left “Down” button
to move the shade to desired Favorite
position.
b. Press and hold (about 2 sec) one “P2”
button on the back of remote control until
motor jog x1.
c. Press and hold (about 2 sec) Left
“Stop” button until motor jog x1.
d. Once more, press and hold (about 2
sec) Left “Stop” button until motor jog x2.
5.3 Delete Favorite Position
a. Press and hold (about 2 sec) one “P2”
button until motor jog.
b. Press and hold (about 2 sec) Left
“Stop” button until motor jog.
c. Once more, press and hold (about
2 sec)
Left “Stop”
button until motor
jog x1.
4.2 Adjust the Lower Limit
a. Press and hold (about 5 sec) Left
“Down” and Left “Stop”
buttons
simultaneously until motor jog x1.
b. Use Left “Down” button to lower
the Bottom Rail then press
Left “Stop”
button when it is in the new desired
lower limit.
c. Press
Right “Down”
button to lower
the Middle Rail, then press Right “Stop”
button when it is in the new desired
lower limit.
d. Press and hold (about 5 sec) Left
“Down” and Left “Stop buttons
simultaneously until motor jog x2.
5.2 Send Shade to Favorite Position
Press and hold (about 2 sec) Left “Stop”
button, motor will move to Favorite
position.
Press
Left “Up”
or
Left “Down”
button
to check if the shade moves in the desired
direction.
If you need to reverse the direction, press
and hold (about 2 sec) Left “Up” and
“Down” buttons simultaneously until
motor jog x1.
3.1 Set Upper Limit
a. Press Right “Up” button to raise the
Middle Rail, then press
Right “Stop”
button when it is in the desired upper limit.
b. Press Left “Up” button to raise the
Bottom Rail, then press Left “Stop”
button when it is in the desired upper limit.
c. Press and hold (about 5 sec) Left “Up”
and Left “Stop” buttons simultaneously
until motor jog x2.
*The operation is only valid when there are no limits.
* Repeat the same procedure to unpair
remote control.
*If you exit the limit setting status before
you finish the limit settings, the motor will
take the previous existing limits.
*If the motor has no response, it already
has a Maximum or Minimum speed.
3.2 Set Lower Limit
a. Press Left “Down” button to lower the
Bottom Rail, then press Left “Stop”
button when it is in the desired lower limit.
b. Press Right “Down” button to lower
the Middle Rail, then press
Right “Stop”
button when it is in the desired lower limit.
c. Press and hold (about 5 sec)
Left
“Down” and Left “Stop” buttons
simultaneously until motor jog x2.
Action on
Motor
Action on
Remote Control
+
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
Motor Response
Middle Rail
Response
Motor Response
Bottom Rail
Response
Left Up Left Down
Left Stop
a.
a.
a.
a.
a.
a.
a.
b.
b.
b.
b.
b.
a.
a.
a.
c.
b.
b.
b.
c.
b.
c.
c.
c.
c.
b.
d.
Jog x2
+
Left Up
Right Up Left Up
Left Stop
a.
a.
b.
b.
Action on
Remote Control
Action on
Remote Control Action on
Remote Control
Motor Response
Bottom Rail
Response Middle Rail
Response
Jog x1
+
Left Down Left Stop
Left Down
Jog x1
Jog x2
+
Left Up Left Down
Left Stop
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
Jog x1
Jog x1
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
+
+
or
Left Up
Lower
Channel
Lower
Channel
Left Down
Higher
Channel
Higher
Channel
Left Stop
Jog x1
Jog x2
Jog x1
Current Remote Control
New Remote Control
Current Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
P2
P2
P2
Jog x1
Jog x1 Jog x1
Jog x2
Jog x1
Jog x2
Left Up
Higher
Channel
Lower
Channel
Left Up
Left Down
Left Down
Stop
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Remote
Response
Motor Response
Motor Response
Remote
Response
Remote
Response
Motor Response
Remote
Response
P2
P2
C
11
O 5
1 15
7.2 New Remote Control
Follow instructions under the section 1.
Pair / Unpair Remote Control
*Repeat the same procedure to remove
additional remote control.
c.
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Bottom Rail
Response
Motor Response
Middle Rail
Response
Jog x2
+
Left Down
Left Down Right Down
Left Stop
a.
b.
c.
P1
d.
Action on
Remote Control
Motor Response
Jog x2
+
Left Down Left Stop
c.
Right Down
a.
b.
Action on
Remote Control
Action on
Remote Control Action on
Remote Control
Motor Response
Middle Rail
Response Bottom Rail
Response
Jog x1
+
Left Up Left Stop
Right Up
d.
Action on
Remote Control
Motor Response
Jog x2
+
Left Up Left Stop
c.
Left Up
Jog x1
Jog x1 Jog x2
Jog x1
Jog x1
Jog x1
or
or
or
Left Up Left Down
Left Stop
Left Stop
Left Stop
Left Stop
Left Stop
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Shade Response
Motor Response
Motor Response
Motor Response
P2
P2
!
Essential Settings
The steps in factory mode must be completed to ensure proper operation.
* All setup needs to
be done using
LEFT
SIDE
of the remote
.
8. Adjust Motor Speed
Channel Options 6. Roller Mode and Sheer Mode
7. Add or Remove Additional Remote
5. Favorite Position
2. Change Motor Direction (if necessary)
3. Setting the Upper and Lower Limits
4. Adjust Limits
1. Pair / Unpair Remote Control
Jog x1
Jog x1
Jog x2
a. Press “P1” button (about 2 sec) on the
End Cap as shown until motor jog x1.
b. In the next 10 secs, press and hold
Left
“Stop”
button on the remote control until
motor jog x2.
4.1 Adjust the Upper Limit
a. Press and hold (about 5 sec) Left “Up”
and
Left “Stop”
buttons simultaneously
until motor jog x1.
b. Press Right “Up” button to raise the
Middle Rail, then press
Right “Stop”
button when it is in the new desired
upper limit.
c. Press
Left “Up”
button to raise the
Bottom Rail, then press Left “Stop”
button when it is in the new desired
upper limit.
d. Press and hold (about 5 sec) Left
“Up” and Left “Stop” buttons
simultaneously until motor jog x2.
6.1 Roller Shade Mode - continue
movement after a short press -
Default Mode
a. Press and hold (about 5 sec)
Left “Up”
and Left “Down” buttons simultaneously
until motor jog x1.
b. Press and hold (about 2 sec) Left
“Stop”
button until motor jog x2.
7.1 Using Current Remote Control
a. On the current remote control, press
and hold (about 2 sec) one
“P2”
button
until motor jog x1.
b. Once more, on the current remote
control, press and hold (about 2 sec) one
“P2”
button until motor jog x1.
c. On the New remote control, press and
hold (about 2 sec) one “P2” button until
motor jog x2.
8.1 Acceleration Speed
a. Press one “P2” button until motor
jog x1.
b. Press
Left “Up”
button until motor
jog x1.
c. Once more, press Left “Up” button
until motor jog x2.
Select A Channel
a. Press “<” button on the remote to
select a lower channel.
b. Press
“>”
button on the remote to
select a higher channel.
6.2 Sheer Shade Mode - jog
movement after a short press
(continue movement after a long
press)
a. Press and hold (about 5 sec)
Left “Up”
and Left “Down” buttons simultaneously
until motor jog x1.
b. Press and hold (about 2 sec)
Left
“Stop”
button until motor jog x1.
8.2 Decelaration Speed
a. Press one
“P2”
button until motor
jog x1.
b. Press Left “Down” button until motor
jog x1.
c. Once more, press Left “Down” button
until motor jog x2.
Hide Unused Channels
a. Press and Hold (about 3 sec) “<” and
“>” buttons simultaneously until remote
control displays “C” (channel).
b. Press
“<” or “>”
button to select
required quantity of channel (between
1 to 15).
c. Press “Stop” button to confirm
selection (the example shows a 5-channel
selection). The LED will display “O” (OK)
once to confirm selection.
5.1 Set Favorite Position
a. Use Left “Up” or Left “Down” button
to move the shade to desired Favorite
position.
b. Press and hold (about 2 sec) one “P2”
button on the back of remote control until
motor jog x1.
c. Press and hold (about 2 sec) Left
“Stop” button until motor jog x1.
d. Once more, press and hold (about 2
sec) Left “Stop” button until motor jog x2.
5.3 Delete Favorite Position
a. Press and hold (about 2 sec) one “P2”
button until motor jog.
b. Press and hold (about 2 sec)
Left
“Stop” button until motor jog.
c. Once more, press and hold (about
2 sec)
Left “Stop”
button until motor
jog x1.
4.2 Adjust the Lower Limit
a. Press and hold (about 5 sec) Left
“Down” and Left “Stop”
buttons
simultaneously until motor jog x1.
b. Use Left “Down” button to lower
the Bottom Rail then press
Left “Stop”
button when it is in the new desired
lower limit.
c. Press
Right “Down”
button to lower
the Middle Rail, then press
Right “Stop”
button when it is in the new desired
lower limit.
d. Press and hold (about 5 sec)
Left
“Down” and Left “Stop buttons
simultaneously until motor jog x2.
5.2 Send Shade to Favorite Position
Press and hold (about 2 sec) Left “Stop”
button, motor will move to Favorite
position.
Press
Left “Up”
or
Left “Down”
button
to check if the shade moves in the desired
direction.
If you need to reverse the direction, press
and hold (about 2 sec) Left “Up” and
“Down” buttons simultaneously until
motor jog x1.
3.1 Set Upper Limit
a. Press Right “Up” button to raise the
Middle Rail, then press
Right “Stop”
button when it is in the desired upper limit.
b. Press Left “Up” button to raise the
Bottom Rail, then press Left “Stop”
button when it is in the desired upper limit.
c. Press and hold (about 5 sec) Left “Up”
and Left “Stop” buttons simultaneously
until motor jog x2.
*The operation is only valid when there are no limits.
* Repeat the same procedure to unpair
remote control.
*If you exit the limit setting status before
you finish the limit settings, the motor will
take the previous existing limits.
*If the motor has no response, it already
has a Maximum or Minimum speed.
3.2 Set Lower Limit
a. Press Left “Down” button to lower the
Bottom Rail, then press Left “Stop”
button when it is in the desired lower limit.
b. Press Right “Down” button to lower
the Middle Rail, then press
Right “Stop”
button when it is in the desired lower limit.
c. Press and hold (about 5 sec)
Left
“Down”
and
Left “Stop”
buttons
simultaneously until motor jog x2.
Action on
Motor
Action on
Remote Control
+
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
Motor Response
Middle Rail
Response
Motor Response
Bottom Rail
Response
Left Up Left Down
Left Stop
a.
a.
a.
a.
a.
a.
a.
b.
b.
b.
b.
b.
a.
a.
a.
c.
b.
b.
b.
c.
b.
c.
c.
c.
c.
b.
d.
Jog x2
+
Left Up
Right Up Left Up
Left Stop
a.
a.
b.
b.
Action on
Remote Control
Action on
Remote Control Action on
Remote Control
Motor Response
Bottom Rail
Response Middle Rail
Response
Jog x1
+
Left Down Left Stop
Left Down
Jog x1
Jog x2
+
Left Up Left Down
Left Stop
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
Jog x1
Jog x1
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
+
+
or
Left Up
Lower
Channel
Lower
Channel
Left Down
Higher
Channel
Higher
Channel
Left Stop
Jog x1
Jog x2
Jog x1
Current Remote Control
New Remote Control
Current Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
P2
P2
P2
Jog x1
Jog x1 Jog x1
Jog x2
Jog x1
Jog x2
Left Up
Higher
Channel
Lower
Channel
Left Up
Left Down
Left Down
Stop
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Remote
Response
Motor Response
Motor Response
Remote
Response
Remote
Response
Motor Response
Remote
Response
P2
P2
C
11
O 5
1 15
7.2 New Remote Control
Follow instructions under the section 1.
Pair / Unpair Remote Control
*Repeat the same procedure to remove
additional remote control.
c.
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Bottom Rail
Response
Motor Response
Middle Rail
Response
Jog x2
+
Left Down
Left Down Right Down
Left Stop
a.
b.
c.
P1
d.
Action on
Remote Control
Motor Response
Jog x2
+
Left Down Left Stop
c.
Right Down
a.
b.
Action on
Remote Control
Action on
Remote Control Action on
Remote Control
Motor Response
Middle Rail
Response Bottom Rail
Response
Jog x1
+
Left Up Left Stop
Right Up
d.
Action on
Remote Control
Motor Response
Jog x2
+
Left Up Left Stop
c.
Left Up
Jog x1
Jog x1 Jog x2
Jog x1
Jog x1
Jog x1
or
or
or
Left Up Left Down
Left Stop
Left Stop
Left Stop
Left Stop
Left Stop
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Shade Response
Motor Response
Motor Response
Motor Response
P2
P2
!
Essential Settings
The steps in factory mode must be completed to ensure proper operation.
* All setup needs to
be done using
LEFT
SIDE
of the remote
.
8. Adjust Motor Speed
Channel Options 6. Roller Mode and Sheer Mode
7. Add or Remove Additional Remote
5. Favorite Position
2. Change Motor Direction (if necessary)
3. Setting the Upper and Lower Limits
4. Adjust Limits
1. Pair / Unpair Remote Control
Jog x1
Jog x1
Jog x2
a. Press “P1” button (about 2 sec) on the
End Cap as shown until motor jog x1.
b. In the next 10 secs, press and hold Left
“Stop”
button on the remote control until
motor jog x2.
4.1 Adjust the Upper Limit
a. Press and hold (about 5 sec) Left “Up”
and
Left “Stop”
buttons simultaneously
until motor jog x1.
b. Press Right “Up” button to raise the
Middle Rail, then press
Right “Stop”
button when it is in the new desired
upper limit.
c. Press
Left “Up”
button to raise the
Bottom Rail, then press
Left “Stop”
button when it is in the new desired
upper limit.
d. Press and hold (about 5 sec)
Left
“Up” and Left “Stop” buttons
simultaneously until motor jog x2.
6.1 Roller Shade Mode - continue
movement after a short press -
Default Mode
a. Press and hold (about 5 sec)
Left “Up”
and Left “Down” buttons simultaneously
until motor jog x1.
b. Press and hold (about 2 sec) Left
“Stop”
button until motor jog x2.
7.1 Using Current Remote Control
a. On the current remote control, press
and hold (about 2 sec) one “P2” button
until motor jog x1.
b. Once more, on the current remote
control, press and hold (about 2 sec) one
“P2” button until motor jog x1.
c. On the New remote control, press and
hold (about 2 sec) one “P2” button until
motor jog x2.
8.1 Acceleration Speed
a. Press one “P2” button until motor
jog x1.
b. Press Left “Up” button until motor
jog x1.
c. Once more, press Left “Up” button
until motor jog x2.
Select A Channel
a. Press “<” button on the remote to
select a lower channel.
b. Press
“>”
button on the remote to
select a higher channel.
6.2 Sheer Shade Mode - jog
movement after a short press
(continue movement after a long
press)
a. Press and hold (about 5 sec)
Left “Up”
and Left “Down” buttons simultaneously
until motor jog x1.
b. Press and hold (about 2 sec) Left
“Stop”
button until motor jog x1.
8.2 Decelaration Speed
a. Press one
“P2”
button until motor
jog x1.
b. Press Left “Down” button until motor
jog x1.
c. Once more, press
Left “Down”
button
until motor jog x2.
Hide Unused Channels
a. Press and Hold (about 3 sec)
“<” and
“>” buttons simultaneously until remote
control displays “C” (channel).
b. Press “<” or “>” button to select
required quantity of channel (between
1 to 15).
c. Press “Stop” button to confirm
selection (the example shows a 5-channel
selection). The LED will display “O” (OK)
once to confirm selection.
5.1 Set Favorite Position
a. Use Left “Up” or Left “Down” button
to move the shade to desired Favorite
position.
b. Press and hold (about 2 sec) one “P2”
button on the back of remote control until
motor jog x1.
c. Press and hold (about 2 sec) Left
“Stop” button until motor jog x1.
d. Once more, press and hold (about 2
sec) Left “Stop” button until motor jog x2.
5.3 Delete Favorite Position
a. Press and hold (about 2 sec) one “P2”
button until motor jog.
b. Press and hold (about 2 sec)
Left
“Stop” button until motor jog.
c. Once more, press and hold (about
2 sec)
Left “Stop”
button until motor
jog x1.
4.2 Adjust the Lower Limit
a. Press and hold (about 5 sec) Left
“Down” and Left “Stop” buttons
simultaneously until motor jog x1.
b. Use Left “Down” button to lower
the Bottom Rail then press Left “Stop”
button when it is in the new desired
lower limit.
c. Press Right “Down” button to lower
the Middle Rail, then press
Right “Stop”
button when it is in the new desired
lower limit.
d. Press and hold (about 5 sec)
Left
“Down” and Left “Stop buttons
simultaneously until motor jog x2.
5.2 Send Shade to Favorite Position
Press and hold (about 2 sec) Left “Stop”
button, motor will move to Favorite
position.
Press
Left “Up”
or
Left “Down”
button
to check if the shade moves in the desired
direction.
If you need to reverse the direction, press
and hold (about 2 sec) Left “Up” and
“Down” buttons simultaneously until
motor jog x1.
3.1 Set Upper Limit
a. Press Right “Up” button to raise the
Middle Rail, then press Right “Stop”
button when it is in the desired upper limit.
b. Press Left “Up” button to raise the
Bottom Rail, then press Left “Stop”
button when it is in the desired upper limit.
c. Press and hold (about 5 sec) Left “Up”
and Left “Stop” buttons simultaneously
until motor jog x2.
*The operation is only valid when there are no limits.
* Repeat the same procedure to unpair
remote control.
*If you exit the limit setting status before
you finish the limit settings, the motor will
take the previous existing limits.
*If the motor has no response, it already
has a Maximum or Minimum speed.
3.2 Set Lower Limit
a. Press Left “Down” button to lower the
Bottom Rail, then press Left “Stop”
button when it is in the desired lower limit.
b. Press Right “Down” button to lower
the Middle Rail, then press Right “Stop”
button when it is in the desired lower limit.
c. Press and hold (about 5 sec) Left
“Down”
and
Left “Stop”
buttons
simultaneously until motor jog x2.
Action on
Motor
Action on
Remote Control
+
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
Motor Response
Middle Rail
Response
Motor Response
Bottom Rail
Response
Left Up Left Down
Left Stop
a.
a.
a.
a.
a.
a.
a.
b.
b.
b.
b.
b.
a.
a.
a.
c.
b.
b.
b.
c.
b.
c.
c.
c.
c.
b.
d.
Jog x2
+
Left Up
Right Up Left Up
Left Stop
a.
a.
b.
b.
Action on
Remote Control
Action on
Remote Control Action on
Remote Control
Motor Response
Bottom Rail
Response Middle Rail
Response
Jog x1
+
Left Down Left Stop
Left Down
Jog x1
Jog x2
+
Left Up Left Down
Left Stop
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
Jog x1
Jog x1
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
+
+
or
Left Up
Lower
Channel
Lower
Channel
Left Down
Higher
Channel
Higher
Channel
Left Stop
Jog x1
Jog x2
Jog x1
Current Remote Control
New Remote Control
Current Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
P2
P2
P2
Jog x1
Jog x1 Jog x1
Jog x2
Jog x1
Jog x2
Left Up
Higher
Channel
Lower
Channel
Left Up
Left Down
Left Down
Stop
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Remote
Response
Motor Response
Motor Response
Remote
Response
Remote
Response
Motor Response
Remote
Response
P2
P2
C
11
O
1 15
7.2 New Remote Control
Follow instructions under the section 1.
Pair / Unpair Remote Control
*Repeat the same procedure to remove
additional remote control.
c.
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Bottom Rail
Response
Motor Response
Middle Rail
Response
Jog x2
+
Left Down
Left Down Right Down
Left Stop
a.
b.
c.
P1
d.
Action on
Remote Control
Motor Response
Jog x2
+
Left Down Left Stop
c.
Right Down
a.
b.
Action on
Remote Control
Action on
Remote Control Action on
Remote Control
Motor Response
Middle Rail
Response Bottom Rail
Response
Jog x1
+
Left Up Left Stop
Right Up
d.
Action on
Remote Control
Motor Response
Jog x2
+
Left Up Left Stop
c.
Left Up
Jog x1
Jog x1 Jog x2
Jog x1
Jog x1
Jog x1
or
or
or
Left Up Left Down
Left Stop
Left Stop
Left Stop
Left Stop
Left Stop
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Shade Response
Motor Response
Motor Response
Motor Response
P2
P2
!
Essential Settings
The steps in factory mode must be completed to ensure proper operation.
* All setup needs to
be done using
LEFT
SIDE
of the remote
.
8. Adjust Motor Speed
Channel Options 6. Roller Mode and Sheer Mode
7. Add or Remove Additional Remote
5. Favorite Position
2. Change Motor Direction (if necessary)
3. Setting the Upper and Lower Limits
4. Adjust Limits
1. Pair / Unpair Remote Control
Jog x1
Jog x1
Jog x2
a. Press “P1” button (about 2 sec) on the
End Cap as shown until motor jog x1.
b. In the next 10 secs, press and hold Left
“Stop”
button on the remote control until
motor jog x2.
4.1 Adjust the Upper Limit
a. Press and hold (about 5 sec) Left “Up”
and
Left “Stop”
buttons simultaneously
until motor jog x1.
b. Press Right “Up” button to raise the
Middle Rail, then press
Right “Stop”
button when it is in the new desired
upper limit.
c. Press
Left “Up”
button to raise the
Bottom Rail, then press
Left “Stop”
button when it is in the new desired
upper limit.
d. Press and hold (about 5 sec)
Left
“Up” and Left “Stop” buttons
simultaneously until motor jog x2.
6.1 Roller Shade Mode - continue
movement after a short press -
Default Mode
a. Press and hold (about 5 sec)
Left “Up”
and Left “Down” buttons simultaneously
until motor jog x1.
b. Press and hold (about 2 sec) Left
“Stop”
button until motor jog x2.
7.1 Using Current Remote Control
a. On the current remote control, press
and hold (about 2 sec) one “P2” button
until motor jog x1.
b. Once more, on the current remote
control, press and hold (about 2 sec) one
“P2” button until motor jog x1.
c. On the New remote control, press and
hold (about 2 sec) one “P2” button until
motor jog x2.
8.1 Acceleration Speed
a. Press one “P2” button until motor
jog x1.
b. Press Left “Up” button until motor
jog x1.
c. Once more, press Left “Up” button
until motor jog x2.
Select A Channel
a. Press “<” button on the remote to
select a lower channel.
b. Press
“>”
button on the remote to
select a higher channel.
6.2 Sheer Shade Mode - jog
movement after a short press
(continue movement after a long
press)
a. Press and hold (about 5 sec)
Left “Up”
and Left “Down” buttons simultaneously
until motor jog x1.
b. Press and hold (about 2 sec) Left
“Stop”
button until motor jog x1.
8.2 Decelaration Speed
a. Press one
“P2”
button until motor
jog x1.
b. Press Left “Down” button until motor
jog x1.
c. Once more, press
Left “Down”
button
until motor jog x2.
Hide Unused Channels
a. Press and Hold (about 3 sec)
“<” and
“>” buttons simultaneously until remote
control displays “C” (channel).
b. Press “<” or “>” button to select
required quantity of channel (between
1 to 15).
c. Press “Stop” button to confirm
selection (the example shows a 5-channel
selection). The LED will display “O” (OK)
once to confirm selection.
5.1 Set Favorite Position
a. Use Left “Up” or Left “Down” button
to move the shade to desired Favorite
position.
b. Press and hold (about 2 sec) one “P2”
button on the back of remote control until
motor jog x1.
c. Press and hold (about 2 sec) Left
“Stop” button until motor jog x1.
d. Once more, press and hold (about 2
sec) Left “Stop” button until motor jog x2.
5.3 Delete Favorite Position
a. Press and hold (about 2 sec) one “P2”
button until motor jog.
b. Press and hold (about 2 sec)
Left
“Stop” button until motor jog.
c. Once more, press and hold (about
2 sec)
Left “Stop”
button until motor
jog x1.
4.2 Adjust the Lower Limit
a. Press and hold (about 5 sec) Left
“Down” and Left “Stop” buttons
simultaneously until motor jog x1.
b. Use Left “Down” button to lower
the Bottom Rail then press Left “Stop”
button when it is in the new desired
lower limit.
c. Press Right “Down” button to lower
the Middle Rail, then press
Right “Stop”
button when it is in the new desired
lower limit.
d. Press and hold (about 5 sec)
Left
“Down” and Left “Stop buttons
simultaneously until motor jog x2.
5.2 Send Shade to Favorite Position
Press and hold (about 2 sec) Left “Stop”
button, motor will move to Favorite
position.
Press
Left “Up”
or
Left “Down”
button
to check if the shade moves in the desired
direction.
If you need to reverse the direction, press
and hold (about 2 sec) Left “Up” and
“Down” buttons simultaneously until
motor jog x1.
3.1 Set Upper Limit
a. Press Right “Up” button to raise the
Middle Rail, then press Right “Stop”
button when it is in the desired upper limit.
b. Press Left “Up” button to raise the
Bottom Rail, then press Left “Stop”
button when it is in the desired upper limit.
c. Press and hold (about 5 sec) Left “Up”
and Left “Stop” buttons simultaneously
until motor jog x2.
*The operation is only valid when there are no limits.
* Repeat the same procedure to unpair
remote control.
*If you exit the limit setting status before
you finish the limit settings, the motor will
take the previous existing limits.
*If the motor has no response, it already
has a Maximum or Minimum speed.
3.2 Set Lower Limit
a. Press Left “Down” button to lower the
Bottom Rail, then press Left “Stop”
button when it is in the desired lower limit.
b. Press Right “Down” button to lower
the Middle Rail, then press Right “Stop”
button when it is in the desired lower limit.
c. Press and hold (about 5 sec) Left
“Down”
and
Left “Stop”
buttons
simultaneously until motor jog x2.
Action on
Motor
Action on
Remote Control
+
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
Motor Response
Middle Rail
Response
Motor Response
Bottom Rail
Response
Left Up Left Down
Left Stop
a.
a.
a.
a.
a.
a.
a.
b.
b.
b.
b.
b.
a.
a.
a.
c.
b.
b.
b.
c.
b.
c.
c.
c.
c.
b.
d.
Jog x2
+
Left Up
Right Up Left Up
Left Stop
a.
a.
b.
b.
Action on
Remote Control
Action on
Remote Control Action on
Remote Control
Motor Response
Bottom Rail
Response Middle Rail
Response
Jog x1
+
Left Down Left Stop
Left Down
Jog x1
Jog x2
+
Left Up Left Down
Left Stop
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
Jog x1
Jog x1
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
+
+
or
Left Up
Lower
Channel
Lower
Channel
Left Down
Higher
Channel
Higher
Channel
Left Stop
Jog x1
Jog x2
Jog x1
Current Remote Control
New Remote Control
Current Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Motor Response
P2
P2
P2
Jog x1
Jog x1 Jog x1
Jog x2
Jog x1
Jog x2
Left Up
Higher
Channel
Lower
Channel
Left Up
Left Down
Left Down
Stop
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Remote
Response
Motor Response
Motor Response
Remote
Response
Remote
Response
Motor Response
Remote
Response
P2
P2
C
11
5
1 15
7.2 New Remote Control
Follow instructions under the section 1.
Pair / Unpair Remote Control
*Repeat the same procedure to remove
additional remote control.
c.
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Bottom Rail
Response
Motor Response
Middle Rail
Response
Jog x2
+
Left Down
Left Down Right Down
Left Stop
a.
b.
c.
P1
d.
Action on
Remote Control
Motor Response
Jog x2
+
Left Down Left Stop
c.
Right Down
a.
b.
Action on
Remote Control
Action on
Remote Control Action on
Remote Control
Motor Response
Middle Rail
Response Bottom Rail
Response
Jog x1
+
Left Up Left Stop
Right Up
d.
Action on
Remote Control
Motor Response
Jog x2
+
Left Up Left Stop
c.
Left Up
Jog x1
Jog x1 Jog x2
Jog x1
Jog x1
Jog x1
or
or
or
Left Up Left Down
Left Stop
Left Stop
Left Stop
Left Stop
Left Stop
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Action on
Remote Control
Motor Response
Shade Response
Motor Response
Motor Response
Motor Response
P2
P2
AMP25B
Instruction
Attention
-1-
The motor is suitable for motorization of roller blinds, sheer shadings, roman shades, and zebra shades.
Never drop, knock, drill or submerge the motor. Keep the power cable in right position as following.
Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
Declarations
d electrical products appropriately.
-2-
Safety
1. Do not expose motor to humid, damp or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna and keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If power cable or connector is damaged, do not use.
6. Ensure correct crown and drive adaptor are used.
7. Ensure power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls shall be properly isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered
operation.
11. Installation and programming to be performed by a qualified professional, use or modification outside
the scope of this instruction may void warranty.
Features
Fields of Application
Specifications
Following data for reference
Working temperature: -10 ℃ ~ +50 ℃
Input Voltage: USB 5V 1A / USB 5V 2A
Radio Frequency: 433.925MHz
Maximum Running Time: 6 minutes
Model
Rated Torque
(N.m)
Rated Speed
(rpm)
Rated Power
(W)
AMP25B - 0.7/34 0.7 34 8
AMP25B -1.1/28 1.1 28 8
Charging Instructions
This motor has a built in Li-ion battery pack with integrated charge management.
Max power input for recharging: 5V 2A.
Before first use please charge motor for 6 hours. Using 5V charger (most phones charger is 5V ) .
During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and
needs to be charged.
During operation, the voltage was detected to be too low, the battery was about to run out, the battery stopped
running and needed to be recharged.
Rechargeable Battery
Blinking red:
Low battery alert
Blinking green:
Charging is processing
Solid green:
Battery has
finished charging.
FCC Text - text 01
Add A zoom in on the
charging port
P1 Button Instructions
P1 button
Lithium Battery Switch
LED light
Micro-USB Port
Add visual explanation of P1 - file 02
Sheer
Roller Revolve Roman shades
Advanced Setting - Disable Limit Setting
a. Remove the cover from the backside of remote,
the lock switch is in the right corner.
b. Move the switch to the “Lock” position to disable
the following commands, remote will show “L” (lock):
- Change Motor Direction
- Setting the Upper and Lower Limit
- Adjust Limit
- Roller Mode or Sheer Mode
c. Move the switch to “Unlock” position to assess all
remote functions, remote will show “U” (unlock).
a.
b.
c.
Switch
Switch
Switch
Lock
Lock
Unlock
Unlock
*This advanced feature is intended to be used after
all shade programming is completed. User Mode will
prevent accidental or unintended changing of limits.
L
U
5