amiad ADI-X IOM Installation, Operation & Maintenance Instructions Manual Download Page 81

Page: 81 / 83

Amiad Water Systems - ADI-X IOM 910101-001180 / 06.2021

Freezing Protection

Freezing Protection – This function is to prevent the filter from freezing in low

temperature while it is connected to water source.

Default value: Enable

Low Temperature Threshold – Temperature setpoint to start filter flushing.

Default value: 4°C.

Protecting Flushing Interval – Flushing Interval while freezing protection Is

activated.

Default value: 60 min.

LCD Display Unit

Allows switching units on the controller screen between bar and psi.

Important note: make sure to press SAVE after changing any of the above settings.

Appendix B. “Alarms and Faults List”

Alert

Possible cause

Recommended Action

Low battery

Low battery voltage

Replace all 4 controller batteries

Low battery pause

Controller paused due to low battery

voltage

Replace all 4 controller batteries

High DP alarm

DP value is >= HDA threshold (units:

bar/100)

Alert only

High DP fault

DP value is >= HDF threshold (units:

bar/100)

Alert only

Continuous mode

alert

Controller exceeded number of

consecutive flushes for alerts

Check configuration/check DP: If high,

perform manual flush with downstream

valve closed, open the filter for

inspection

DFU failed

Firmware update fail

Validate cellular reception and try again

Out of range app

connection

Controller out of range during

connection session

Get closer to the controller with the

mobile device (within Bluetooth® range)

Sensor pressure read

failed

The number of the sensor that failed

to read. Inlet (0), Outlet (1), Piston (2).

If continues - contact support

There is a vacuum in the system

Perform air release

Equip the system with anti-vacuum valve

Capacitor charger

start failed

Unable to charge capacitor

Contact support

Load capacitor

timeout

Capacitor charge timeout

Check battery voltage level, contact

support

Low downstream

pressure

The outlet pressure is less than 1.5 bar Check the filter and the water system

High upstream

pressure

The inlet pressure is greater than

maximum allowed pressure for the

filter

Adjust the water system inlet pressure

Anti-Freeze Active

Freezing Protection start, as a result of

Low Temperature Threshold

Anti-Freeze Exit

Stop Freezing Protection procedure

Summary of Contents for ADI-X IOM




















































































Search results

Summary of Contents for ADI-X IOM

Reviews:

Brands by name

Popular brands

amiad ADI-X IOM, Installation, Operation & Maintenance Instructions Manual

Search results

Summary of Contents for ADI-X IOM

Reviews:

Brands by name

Popular brands