manualshive.com logo in svg

AMF Reece 101, Installation Manual, Page: 12 / 60

Share
Download
AMF Reece 101 Installation Manual Download Page 12

S-101

e-mail: [email protected]; [email protected]; website: www.amfreece.com

Phones: +420 582 309 146 (Service), +420 582 309 286 (Spare Parts); Fax: +420 582 360 606

Revised  09/2004

1-10

CONTENTS

CUT BEFORE - MACHINE ADJUSTMENTS ............................................................... 1-20

CORD TRIM

Threading diamgrams ........................................................................................... 1-23
Upper thread draw-off and tension adjustments ................................................. 1-24
Thread pick-up adjustments ................................................................................. 1-24
Under thread draw-off and tension release .......................................................... 1-24
Thread trimmer and thread retainer ..................................................................... 1-25
To set the under thread quide ............................................................................... 1-26
Shear adjustment ................................................................................................... 1-26
To adjust the hold down finger ............................................................................. 1-26

ADJUSTMENT FOR THE ADJUSTABLE FLY BAR MACHINE ............................... 1-27

CUT BEFORE ENDGING MACHINE ............................................................................ 1-29

NEEDLES ........................................................................................................................... 1-30

Summary of Contents for Reece 101





























































Reviews:

No comments