SXRXLXX1 - SIL IntelliPoint RF Series User's Manual
18
Mode 3: Auto-Cal 2 pF.
This mode provides a 2 pF preload; alarm setpoint varies depending on
material and coating deposit changes.
Mode 4: Fixed Cal 2 pF.
This mode provides a 2 pF preload; alarm setpoint is locked to starting
capacitance value recorded at system start-up.
Calibration Mode changes
Mode Selection change must be performed with the sensing
element in air (Material below sensing element).
1. On the RF circuit board (
Figure 2-8
), temporarily remove
the shunt jumper from the “Time Delay Selection Jumper”
and place it on pins 1 & 2 of JP5. The green LED will go out,
and the red LED’s will begin to flash. The number of flashes
indicates which mode the unit is in: 1, 2, 3, or 4.
2. To change modes, press and hold the ReCal button (next
to JP 5). The unit will cycle through the modes: first it will
flash one time – then pause, this indicates mode #1. It will
then flash twice then pause, indicating mode #2, then mode
#3, etc. It will scroll through all 4 modes then start over
again at mode #1. Release the button when it reaches the
desired mode. The LED’s will now flash the number of times
indicating which mode has been selected.
3. Remove the shunt from pins 1 & 2 of JP5 and replace it on
the “Time Delay Selection Jumper” pins from which it was
removed. The unit will remain in the new selected calibration
mode. Put the lid back on the housing securely.
2.9.2
IntelliPoint Calibration Mode Change (Continued)
A full system proof test must be performed when:
- Any system component is changed or replaced by the user.
- Any system component or setting is modified by the user.
A full system proof test must be performed when:
- Any system component is changed or replaced by the user.
- Any system component or setting is modified by the user.
Summary of Contents for SIL IntelliPoint RF S*R*L Series
