background image

8

PREPARATION FOR ASSEMBLY

READ ALL INSTRUCTIONS in the Owner’s Manual before you start.

VERIFY PARTS. Remove all parts from the box and arrange on a smooth clean surface. Verify that you have all the parts 
listed in the below “Parts List”. 

If you have any questions or need help, contact Customer Service at 1-800-251-7558 or go to www.mecocorp.com. Be sure 
to have the grill model number listed on the front cover of this Manual. If you need replacement parts, look in the Parts List to 
fi nd the exact parts you need. If you need a replacement part under warranty, a proof of purchase will be necessary. You will 
be asked to forward your proof of purchase via e-mail, or to fax your proof of purchase to 423-639-2570 and reference your 
model number. It is important to register your grill and retain your receipt.

Tools Required for Assembly:

or                                         or

Phillips and/or 

Straight Screwdriver

Pliers

3/8” Wrench

Adjustable Wrench

ASSEMBLY INSTRUCTIONS

ASSEMBLE SQUARE SUPPORT TUBES TO CROSSBRACES TO MAKE “H-FRAME”

Align hole in end of square Support Tube (12) with second hole of Crossbrace (11). (FIG. A)  Make sure that the 
Support Tube is oriented with fi ve holes on top. The two large holes on the adjacent side are not used. Insert 
1-1/2” Bolt (2) through holes and thread KEPS Nut (6) onto Bolt. Tighten KEPS Nut securely.
Repeat with the second Support Tube at the second hole from the opposite end of the Crossbrace. (FIG. B) Insert 
1-1/2”’ Bolt through holes and thread KEPS Nut onto Bolt. Repeat assembly for second Crossbrace on the other 
end of the Support Tubes. (FIG. C) Tighten all Lock Nuts securely.

(FIG A)

(FIG B)

(FIG C)

2

6

12

11

TOP

Summary of Contents for 9350 Series

















Reviews: