background image

© American Time

4

DSY261RSAE Owner's Manual

IMPORTANT INSTALLATION AND WARRANTY INFORMATION

WARRANTY INFORMATION:

 American Time (the Manufacturer) provides a limited warranty to the Original Purchaser of this 

product. The Original Purchaser is the party to whom the Manufacturer issued its Sales Order, generally the Manufacturer’s 
distributor. In order to preserve this warranty, it is important that only persons who have been properly trained and authorized by 
the Manufacturer service the product.

Other parties involved in the installation of this product may have also provided a warranty, which may be different than that of the 
Manufacturer. The Manufacturer will only be responsible to the Original Purchaser and only for the
Manufacturer’s own warranty. For further information regarding the Manufacturer’s warranty, contact the Original
Purchaser.

OWNER’S MANUAL:

 The owner’s manual does not purport to cover all the details or variations in the equipment described, 

nor does it provide for every possible contingency to be met in connection with installation, operation and maintenance. All 
specifications subject to change without notice. Should further information be desired or should particular problems arise which 
are not covered sufficiently, the matter should be referred to the Installer or Original Purchaser listed below.

INSTALLER INFORMATION

COMPANY:  

INSTALLER:  

PHONE: 

ADDRESS:       

CITY:  

STATE:                 ZIP:

DATE INSTALLED:  

INSTALLER’S SIGNATURE: 

ORIGINAL PURCHASER INFORMATION

COMPANY:  

 

PHONE: 

ADDRESS:  

CITY:  

STATE:                  ZIP:

PURCHASER’S PURCHASE ORDER NO: 

DATE PURCHASED: 

ATS SALES ORDER ACKNOWLEDGMENT NO.: 

ORIGINAL PURCHASER’S SIGNATURE: 

NOTE:

 A copy of the above-completed information may be required by the Manufacturer for authorization of Warranty services.

Summary of Contents for DSY261RSAE




















Reviews: