manualshive.com logo in svg

American Standard Triumph 7034, Installation Instructions Manual, Page: 3 / 7

Share
Download
American Standard Triumph 7034 Installation Instructions Manual Download Page 3

COMPRESSION

NUT

3/8” COMPRESSION

CONNECTION

COUPLING

NUT

FLEXIBLE

SUPPLIES

3/8 O.D.

BULL-NOSE

RISERS

Thread CABLE CONNECTOR 

(1) 

clockwise

onto DRAIN BODY CONNECTION 

(2)

 and

hand tighten. 

Fig.

 

A.

Your new POP-UP DRAIN installation is
now complete. 

Fig.

 

B.

Note: 

Tailpeice on pop-up drain is 1-1/4” O.D.

Fig.

 

B.

Fig.

 

A.

ATTACH CABLE CONNECTOR

6

2

1

Operate LIFT KNOB 

(1)

 to verify that STOPPER 

(2) 

opens and

closes.

Note: 

If STOPPER 

(2)

 does not open and close properly then refer

to the “troubleshooting section” of these instructions.

CHECK OPERATION OF POP-UP

7

1-1/4” O.D.

Fig.

 

B.

1/2" PIPE

THREAD

2

1

Connect water supply to FAUCET 

(1)

 with 1/2" IPS FLEXIBLE

SUPPLIES 

(2)

 or 3/8" O.D. BULL-NOSE RISERS 

(3)

.

Use adjustable wrench to tighten connections. Do not over tighten.

Be careful not to kink copper supply when bending. Use tubing

cutter to cut to proper length.

Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to

waste outlet.

MAKE WATER SUPPLY AND WASTE CONNECTIONS

8

FERRULE

1

2

3

NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE

PURCHASED SEPARATELY.

HOT

COLD

3 

M 9 6 8 8 6 5   R e v .   1 . 2

Summary of Contents for Triumph 7034








Reviews:

No comments