manualshive.com logo in svg

American Standard Triumph 7034, Installation Instructions Manual, Page: 1 / 7

Share
Download
American Standard Triumph 7034 Installation Instructions Manual Download Page 1

M 9 6 8 8 6 5   R e v .   1 . 2

7034

Certified to comply with ANSI A112.18.1

Installation

Instructions

TRIUMPH

Centerset Lavatory Faucet with

Speed Connect™ Drain 

Adjustable Wrench

 Screwdriver

Channel Locks

Recommended tools

Tubing Cutter

1

INSTALL FAUCET

SINK OR

MOUNTING

SURFACE

POP-UP

CABLE

Turn off hot and cold water supplies before beginning.

Insert FAUCET 

(1)

 and CABLE CONNECTOR 

(2)

 through

mounting holes of Sink or mounting surface. 

Fig.

 

A.

Assemble LOCKNUTS 

(3)

 onto SHANKS 

(4)

 from under

side of Sink. Hand tighten firmly. 

Fig.

 

B.

 

2

2

1

4

3

3

4

(HAND TIGHTEN)

*Your new American Standard faucet is designed to work only with the Speed Connect Drain.  Helpful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Fig.

 

A.

Fig.

 

B.

1

Congratulations on purchasing your American Standard faucet
with the Speed Connect Drain,  a feature found only on 
American Standard faucets.

Speed Connect Drain*

•  1/3 of the parts, installs in 1/3 of the time
•  No tools needed
•  Never needs adjustment
•  Guaranteed to seal properly the first time, every time.

Turn off water at

main supply.

CAUTION

Summary of Contents for Triumph 7034








Reviews:

No comments