background image

1

Under no circunstances is the manifacturer to be held liable for any water damage in connection with this water heater.

CONSUMER RESPONSIBILITIES

THIS MANUAL HAS BEEN PREPARED TO ACQUAINT YOU WITH THE INSTALLATION, OPERATION AND 
MAINTENANCE OF YOUR GAS WATER HEATER AND TO PROVIDE IMPORTANT SAFETY INFORMATION.
WE URGE YOU TO READ ALL INSTRUCTIONS THOROUGHLY before attempting installation or operation of 
your water heater. Keep these instructions for future reference.

The manufacturer of this water heater will not ne liable for any damages caused by failure to comply with the installation and 
operating instructions outlined on the following pages. These instructions are a guide for the correct installation of your water 
heater. If you lack the necessary skills required or have difficulty following the directions, you should not proceed but get help 
from a qualified person for that part of the installation you do not understand. Failure to follow this warning can result in an 
incorrect installation that can result in

 

DEATH, INJURY OR PROPERTY DAMAGE.

This water heater is design-certified by CSA International as a power vent water heater, which takes
it’s combustion air, either from the installation area or from air ducted to the unit from outside.

This water heater must be installed according to all local and state codes, or in the absence of local and state codes, the “ 
National Fuel Gas Code”,ANSI Z223.1 (NFPA 54)-Latest Edition. This code is available from the following:

          

Important WARNINGS:

 

Do not use this appliance if any part has been under water. 

Immediately call a qualified service technician.. Water heaters subjected to flood conditions,

or anytime the gas controls, main burner or pilot have been submerged in water, require replacement

of the entire water heater.

American Gas Association 
400 North Capitol, St;  NVV
Washington D.C. 20001-0000
E mail AGA.org

National Fire Protection Agency
1 Batterymarch Park
Quincy, MA 02269
Check your local phone listings for the local authorities having 
jurisdiction over your instalation.

• 

This water heater may not be installed in a mobile home.

• 

Location selection should be as close to the stack or chimney as 
practical and as centralized with the piping system as possible.

• 

Water heater should be located in an area not subject to freezing 
temperatures.

• 

The water heater should be located so that the controls and 
drain are easily accessible (at least 24 inches of open space of  the 
water heater).

• 
• 

A suitable drain pan must be installed under the heater. 

• 

Remove exterior packaging and place installation 
components aside.

• 

Inspect all parts for damage prior to installation 
and startup.

• 

Completely read all instructions before 
attempting to assemble and install this product.

When referring to your water heater always have the 
information listed on the rating plate readily available.

WARNING

WARNING

UNPACKING THE

 

Water Heater

Such pans must have a minimum length and width of at least two 
inches greater than the diameter of the heater, and must be piped 
to an adequate drain. The pan must not restrict combustion air flow. 
(Figure 1)

LOCATION

Use two or more people to move and install water heater, 
unless proper handling equipment is utilized. Failure to do so 
can result in back or other injury.

Important: Do not remove any permanent instructions, labels, 
or the data label from outside of the water heater or on the 
inside of panels.

Summary of Contents for Standard Residential













































Reviews: