background image

All American Standard Products Are Water Tested At Our Factory. 
Some Residual Water May Remain In The Valve During Shipping. 

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years. To ensure that your 
installation proceeds smoothly--please read these instructions carefully before you begin.

UNPACKING

1. Remove the Flush Valve items from the carton. The illustration below shows all items after 
they have been removed from the carton. Some items may be packaged partially assembled to 
other items.

9

8a

1

3

2

4

7c

7a

7b

5

DO NOT REMOVE PROTECTIVE FILM FROM SENSOR

EYE UNTIL INSTALLATION IS COMPLETE.

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH  CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A

CLOTH WITH A COARSE SURFACE.

CARE INSTRUCTIONS FOR CHROME PLATED ITEMS:

7c. Vacuum Breaker Flush Connection
      (Top Spud)
8a. AC Power Supply [Model# 6067]
8b. DC Power Supply
8c. 10’ Extension Wire for Multi-AC
9. Installation Instructions

1. Flush Valve Assembly
2. Electrical Box
3. Cover Plate with Sensor
4. Supply Stop

5. Sweat Solder Adapter 
6. Manual Override Hoses

7a. Vacuum Breaker Flush Connection
      (Wall-Mount Back Spud)

7b. Vacuum Breaker Flush Connection
      (Floor-Mount Back Spud) 

T O P

8b

8c

1

6

Installation Instr

uctions

In

s

t

a

ll

a

t

io

n

 I

n

s

t

r

u

c

t

io

n

s

(In Toronto Area only: 1-905-3061093)

Certified to comply with ASME A112.19.2M

© 2009 AS America, Inc.

NOTE TO INSTALLER: Please give this manual to the customer after installation.

SELECTRONIC™

PROXIMITY TOILET

CONCEALED FLUSH VALVE

1.28 & 1.6 GPF

Concealed Flushometer
for 1-1/2

"

 Top or Back Spud Bowls

CLOG RESISTANT

• Self-cleaning piston valve prevents clogging and reduces maintenance.

ONE SENSOR FITS ALL

• Only 1 sensor for entire Selectronic™ line of faucets, urinals, and
  flush valves.
• Range can be adjusted manually or with optional remote control.
• Sensor Features Low Battery Indicator.

M968550 REV. 1.5

To learn more about American Standard Faucets visit our website at: 

www.americanstandard-us.com

or U.S. customer's e-mail us at: 

[email protected]

For Parts, Service, Warranty or other Assistance, 

please call

 

1-800-442-1902 (In Canada: 1-800-387-0369)

(In Toronto Area only: 1-905-3061093)

6065.22X
6067.22X 
6068.22X

MODEL NUMBERS

6065.26X
6067.26X
6068.26X

M968550 REV. 1.5

Summary of Contents for SELECTRONIC 6065.22 Series















Reviews: