American Standard QR031 Owner'S Manual Download Page 13

 13 CONGLOM .COM
 

 

Please contact 1-877-333-0098 for further assistance .

Operation

 

There are four buttons, ON/OFF, SPEED, LIGHT and CLOCK SETUP . 

 

The center screen will show the clock (12 hour) .

1

2

3

4

5

Turning ON/OFF the unit

 

- Press (5) to turn on the power . 

When you turn the power on, the unit starts working in 
high speed, the clock indication on the center screen (3) 
will go off and "3" will be indicated on the screen . (During 
the operation speed indication will be indicated on the 
screen) .

 

- Press (5) twice to turn off the unit while it is operating . 

While the fan is off, the screen will display the time .

Delay shut off function

 

- While the fan is working, press (5) once, the fan and lights 

will automatically turn off after 2 minutes . 
The screen will indicate "2:00" and start counting down . 
Once the countdown is completed, the range hood will 
beep, the fan and lights will turn off automatically and the 
clock will show in the screen .

During the countdown operation:

 

- You will still be able to change the speed by pressing (4) .

 

- Press (5) once more to stop the fan immediately .

To change fan speed

While the unit is operating:

 

- Press the fan button (4) once, range hood will change to 

medium speed and "2" will be indicated on the screen .

 

- Press the fan button (4) again to change to low speed and 

"1" will show on the screen .

Turning ON/OFF the light

 

- Press the light button (2) to turn the light on and off . 

Set up the clock function

 

- Press the clock button (1) once, the center screen starts flashing "00:00" .

 

- Press the light button (2) to change the hour display and the fan button (4) to change the minute display .

 

- During the setup, if no button is pressed for more than 5 seconds, the setting displayed will be fixed . 

The setup can be done while the unit is running or not .

Summary of Contents for QR031




















Reviews: