American National Manufacturing Static LAL 8100 User Instruction Manual Download Page 10

 

10 of 16 

 

8100 LAL 

Mattress Cleaning Instructions: 

 
 
WARNING and CAUTION: 

 

A.  It is recommended that gloves and protective clothing be worn at all times during cleaning 

and disinfecting 

B.  Hypercarbonate and phenol based solutions 

should not

 be used. 

 
During Operation: 
 

For normal soil, wipe down cover and interior sacs with a standard cleaning disinfectant and 
wipe off excess moisture with a towel. 

 
Laundering Mattress: 

1.  Disconnect the power from the Control Unit and deflate the interior sacs. 
2.  Disassemble cover, interior sacs, connecting hoses, and base.  Place them in different 

laundering baskets. 

3.  The interior sacs must be hand cleaned only.  DO NOT place in sterilization room or 

chamber.  Use a spray disinfectant to wipe down interior sacs.  Air-dry sacs. 

DO NOT 

expose to heat.

 

4.  Spray disinfectants and wipe down foam cover. 
5.  Place cover and base

 ONLY

 in washing machine. 

6.  Use standard hospital disinfectant/detergent. 
7.  Set washing cycles as recommended below: 

Regular Cycle

 

a)  Pre-soak with disinfectant/detergent with diluted bleach in cold water (10 

minutes.) 

b)  Main wash for 15 minutes (Time depending on soil level). 
c)  Rinse Cycle: 5 minutes minimum. 
d)  Spin/Drain Cycle: 5 minutes minimum. 
e)  Air-dry or place in dryer at very low or no heat. 

8.  After the cover, interior sacs, and base are dry, store them in a sterilized bag and seal for 

next use. 

 

NOTICE:

  DO NOT use water temperatures greater than 150°F (65°C). 

Summary of Contents for Static LAL 8100

















Reviews: