background image

 

August 18, 2003 

8.

 

Carefully reinstall the printed circuit board into the front panel lid, aligning the 
LCD display pins with the connector in the printed circuit board, aligning the 
POWER LED with its socket in the lid, and aligning the READ switch with its 
opening in the lid. 

9.

 

Reinstall the READ switch cap and guard. 

10.

 

Reconnect all the internal cable connectors to the printed circuit board with the 
same orientation and position as recorded in Step 3. 

11.

 

Close up the Model 150A enclosure by retightening the four hold-down screws 
in the front panel lid, attaching the lid to the base. 

 
 

V.

 

WARRANTY 

All products manufactured by AMI are warranted to be free of defects in materials and 
workmanship and to perform as specified for a period of one year from date of shipment.  In the 
event of failure occurring during normal use, AMI, at its option, will repair or replace all products 
or components that fail under warranty, and such repair or replacement shall constitute a 
fulfillment of all AMI liabilities with respect to its products.  Since, however, AMI does not have 
control over the installation conditions or the use to which its products are put, no warranty can 
be made of fitness for a particular purpose, and AMI cannot be liable for special or consequential 
damages.  All warranty repairs are F.O.B. Oak Ridge, Tennessee, USA. 

VI.

 

RETURN AUTHORIZATION 

Items to be returned to AMI for repair (warranty or otherwise) require a return authorization 
number to ensure your order will receive proper attention.  Please call an AMI representative at 
(865) 482-1056 for a return authorization before shipping any item back to us. 

Summary of Contents for 150










Reviews: