American Landmaster 18931-R Installation Instructions Manual Download | Manualshive

Page: 9 / 10

background image

19148 Winch Installation Guide Rev A

Page 9 of 10

Figure 15: Remote Winch Capped Off

Figure 16: Remote Winch Switch hooked up

13.

Connect the white two pin connector of the winch harness to the winch contactor two pin white connector.

Figure 17: Connecting the Contactor to the Winch Harness

14.

Attach the winch harness switch connector to the winch switch in the dash.

15.

Locate the black ten pin connector on the winch harness and route it up to the rear of the seven switch panel.

16.

Be sure to install the switch harness connector in the correct orientation. Line up the hook on the switch with the latch
on the harness connector. The hook is on the bottom side of the switch. Place one hand on the front of the switch while
installing the harness connector on the rear. A rocking motion will make installing the harness connector easier. Ensure
that the connector is lined up with the switch and do not bend the switch pins. Do not force the connection. Push the
harness connector onto the switch until the two meet with no gap between them.

«
...
7
8
9
10
»

Summary of Contents for 18931-R











Reviews:

No comments

Related manuals for 18931-R

40.2 ST EL Series

Brand: Harken Pages: 2

Brand: Tulsa Pages: 24

Brand: Prowinch Pages: 22

Brand: Allied Pages: 121

Brand: Warn Industries Pages: 2

Strong-Arm CHP 250

Brand: Clarke Pages: 8

Brand: Horn Tools Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands