VIEW MANAGER 96 ENHANCED TOUCH TRACKER
8000-0748-02, REV. B1
INSTALLATION INSTRUCTIONS
3 of 6
Installing Enhanced Touch
Trackers
Installation Kit (0351-0474-01):
Description
Quantity Part
Number
CABLE ASSY,MDLR,RJ-45,8 COND,14 1
6003-0047-01
SCR,THD CUT,M2.9X9.5,PHP,ST,Z,
1
5899-0004-102
ANCHOR,PLASTIC,#4-#8,3/4"
2
2880-0083-01
SCR,TYP AB,PHP,CAD,#8X1"
2
2816-7634-44
CONN,PLUG,TUBLR,.200CTR,26-12A
1
2109-0254-04
LUG,SPADE,CRIMP,INSUL,22-16AWG
3
2141-0002
CABLE,3COND,18AWG,PVC
16.50 ft
6002-0024-01
INTERCONNECT BOX,TOUCH TRACK 1
0300-1000-01
WARNING—RISK OF ELECTRIC
SHOCK!
Disconnect AC power to the VM96
System and External Interconnect
Module before starting to install this
equipment. Failure to do so could
shock you and may damage the VM96
system or attached devices.
CAUTION—ELECTROSTATIC
SENSITIVE DEVICE!
Follow proper handling procedures to
prevent component failure.
1. Review the network design to determine which
Touch Tracker controllers (controller) must be
terminated. Set jumper E1 on EIMs requiring
termination (Figure 6).
2. Mount each EIM on a wall or other surface
within 3m (10') of its attached controller. Then
route a twisted-pair SensorNet cable from the
VM96 console, past each EIM, until the last
EIM is reached. Do not cut the cable at each
EIM.
3. Referring to Figures 6 through 8:
a. Wire each EIM’s power supply leads to
pins 2, 3, and 4 of a 5-pin compression
connector (one connector per EIM). Tighten
the fastening screws to secure the wires.
b. Strip 25mm (1") of outer insulation from the
SensorNet cable at each EIM location.
Then strip 12mm (.5") of insulation from
each wire.
c. Bend the two wires in the middle of the
stripped area. Insert one wire into pin 1,
and the other into pin 5 of the EIM's 5-pin
compression connector. Tighten both
fastening screws to secure the wires.
d. After attaching power and SensorNet
cables, plug the wired 5-pin connector into
each EIM's WAG005 connector. See Figure
6.
e. Connect the EIM SensorNet cable to the
SensorNet card or preceding SensorNet
device. Then connect the cable between
the last EIM and the next SensorNet
device.
f. Plug the modular interconnect cable into
the RJ-45 connector on the back of the
Touch Tracker controller. Use the strain
relief. Plug the other end into the EIM.
Figure 6: EIM Board Layout.
3 2 1
J1
J2
J3
A
SSY
03
01
-0
3
40
-0
1 R
E
V
-
E1
1-2 TERMINATED
2-3 UNTERMINATED
3 2 1
Figure 7: Installing one Touch Tracker.
J3
J2
2 1
3
4
5
P1
J2
1
2
3
4
Terminated
Power & SensorNet
Connector - WAG005
Touch Tracker Connector
RJ-45
RS-232 connector
DB-9(F)
T
OUCH
T
RACKER
Power
Supply
SensorNet
Link
VM96 card,
J-Box link,
or other
SensorNet
device
SensorNet A
SensorNet B
24Vac A
Ground
24Vac B
RJ-45 Cable
EIM
Strain Relief
