FOUR BAY SYSTEMS, 64 CAMERAS x 16 MONITORS
Systems for a maximum of 64 cameras and 16 monitors are
supplied in four bays. The AD1653B bay contains a power
supply, processor, and monitor modules for monitors 1 - 8.
The AD1657 bay contains a power supply and monitor
modules for monitors 9 - 16. The AD1654 bay contains
camera modules for cameras 1 - 64 for monitors 1 - 8. The
AD1656 bay contains camera modules for cameras 1 - 64 for
monitors 9 - 16.
These systems are supplied in four bays configured as shown
below:
AD1653BAD1657AD1654 AD1656
Modules/Panels
Bay
Bay
Bay
Bay
AD1603N PSM, Pwr Pnl
1
1
-
-
Power Panel
-
-
1
1
AD1663B CPM, Data Pnl
1
-
-
-
AD1609CM VIM
-
-
-
1-8
AD1611 VIM
-
-
1-8
-
AD1626 VOM
4
1-4
-
-
VIP Panel
-
-
1
1
For illustration of a typical Four Bay system with 64 cameras
and 16 monitors, see Page C-12 of the Typical System
Connections.
IDENTIFY ALL BAYS, MODULES, AND PANELS
CAREFULLY BEFORE PROCEEDING.
Power/Data Interconnections
Two Power/Data Interconnection cables are supplied. Connect
one cable between connector J1 on the AD1653B Power Panel
and connector J1 on the AD1654 Power Panel. Connect the
second cable between connector J1 on the AD1657 Power
Panel and connector J1 on the AD1656 Power Panel.
One Data Interconnect cable is supplied. Connect the Data
cable between connector J3 on the Data Panel in the AD1653B
bay and connector J3 on the Power Panel in the AD1657 bay.
Control Code Connections
Control Code for all 64 cameras is provided from flying leads
on either of the two Power/Data Interconnection cables, above.
Video Interconnections
The camera video outputs from the VIP Panels on the AD1654
and AD1656 bays are provided through eight BNC’s, labeled
1, 3, 5, 7, and 2, 4, 6, 8.
Each AD1626 VOM in the AD1653B and AD1657 bays has
two pairs of input BNC’s located on the upper portion of its
back panel, for video interconnections from the VIP panels.
Outputs from the VIP Panels in the AD1654 and AD1656 bays
connect to the AD1653B and AD1657 bays “A” MONITOR
BNC’s. The “B” MONITOR BNC connectors are not used in
systems with 64 cameras or less.
From the rear of the AD1653B bay, the input BNC for system
monitor 1 is located at the right-most VOM position, labeled
MONITOR 1 A, and system monitor 2 is labeled MONITOR 2
A. System monitor 3 is on the next panel to the left, labeled
MONITOR 3A, and system monitor 4 is labeled MONITOR 4
A, and so on to system monitor 8.
In the AD1657 bay, the input BNC for system monitor 9 is
located at the right-most VOM position, labeled MONITOR 9
A, system monitor 10 is labeled MONITOR 10 A. System
monitor 11 is on the next panel to the left, labeled MONITOR
11 A, system monitor 12 is labeled MONITOR 12 A, and so
on to system monitor 16.
AD1654 to AD1653B - Connect the top BNC on the AD1654
bay VIP Panel, labeled 1, to the top input BNC of the
AD1653B bay VOM panel for system monitor 1, labeled
MONITOR 1 A. Connect the BNC labeled 2 on the AD1654
bay VIP panel, to the top input BNC of the AD1653B bay
VOM panel for system monitor 2, labeled 2 A. Continue in
this manner until all eight connections of the AD1654 bay VIP
panel are connected to all eight “A” monitor inputs of the
AD1653B bay VOM panels.
DO NOT TERMINATE THE VIP PANELS.
AD1656 to AD1657 - Connect the top BNC on the AD1656
bay VIP Panel, labeled 1, to the top input BNC of the AD1657
bay VOM panel for system monitor 9, labeled MONITOR 9 A.
Connect the BNC labeled 2 on the AD1656 bay VIP panel, to
the top input BNC of the AD1657 bay VOM panel for system
monitor 10, labeled 10 A. Continue in this manner until all
eight connections of the AD1657 bay VIP panel are connected
to all eight “A” monitor inputs of the AD1657 bay VOM
panels. If there are less than 16 monitors in the system, leave
the remaining VIP panel BNC’s unterminated.
DO NOT TERMINATE THE VIP PANELS.
SYSTEM CONFIGURATIONS
AD1650B
3-8
