background image

 

ADACSNET USB CONTROL MODULE 

8200-0310-01, REV. B 

INSTALLATION GUIDE 

5 of 6

 

Specifications 

USB Specifications 

Bit rate .............................. 1.5Mb/s Low Speed, 12Mb/s 

Full Speed 

Maximum cable length...... 3m (9.8ft) for 1.5Mb/s,  

5m (16.4ft) for 12Mb/s 

Specification ..................... Universal Serial Bus USB 

Specification Revision 1.1 

Connector ......................... USB Type B receptacle 
Power source.................... From USB host controller port 

(power adaptor not required) 

SensorNet Specifications 

Address range .................. 1 to 254 (configurable) 
Bit rate .............................. 230.4Kbps 
Network distance .............. 1km per node 
Maximum loads................. 32 per node 
Node repeaters ................. SensorNet junction boxes 
Topologies supported ....... Daisy chain, Backbone, or 

Star 

Transmission medium....... Single non-polarized 

unshielded twisted pair UTP 
22AWG 

Connector ......................... Euro-style 2 pin removable 

plug 3.5mm terminal block 

Terminating resistor .......... 120 ohms, switch selectable 
Physical layer ................... RS-485, transformer isolated, 

2-wire 

Data encoding .................. FM-0 
Link layer framing ............. SDLC/HDLC 
Link layer channel............. Bi-directional, half duplex 
Collision avoidance........... Polling by USB Module 
Application protocol .......... Proprietary 
Network nodes.................. Domes, junction boxes, 

secondary TouchTracker™, 
and SensorNet I/O unit 

Power 

Input voltage ..................... 5.0Vdc ±5%, 0.75W 
Internal voltage  
(CPU + Misc. Support)...... 3.3Vdc ±5% 

Surge Protection 

SensorNet: 

Gas discharge tube impulse rated at: 

DC breakdown voltage....................................... 90V 
Insulation resistance ..................10,000 Mega ohms 
Capacitance ...............................................2pF max. 
8/20µs impulse 
discharge current ............................................. 10kA 
Ten 8/20µs impulses  
discharge current ............................................... 5kA 

Isolation transformer coupled ...................... 2000Vrms 
PTC re-settable fuse protects transformer 

Transient voltage suppressors (TVS): 

Break down voltage ................................... 7.6–9.3V 
Peak current....................................................... 40A 
Capacitance .....................................2000pf @ 1kHz 

USB: ESD suppressors protect USB lines by 
suppressing fast rising transients as specified in IEC 
61000-4-2 and MIL-STD-883C (8kV discharge method). 

Environmental 

Operating Temperature: ......... 10° to 50°C (14° to 122°F) 
Relative Humidity: ....................0 to 95% non-condensing 

Mechanical 

Length .......................................................... 10.2cm (4in) 
Width.............................................................. 7cm (2.8in) 
Thickness ...................................................... 2.5cm (1in) 
Weight ......................................................  0.5kg (1.1 lbs) 

Summary of Contents for ADACSNET







Reviews: