American Dryer Corp. AD-30x2 Installation & Operator'S Manual Download Page 3

Page: 3 / 12

113574 - 4

www.adclaundry.com

30x2

11.3

14.0

4.2

4.5

8.3

18.1

35.6

5.1

4.7

170.0

45x2

13.8

16.9

4.2

31.1

4.2

21.3

13.6

7.3

6.9

204.3

Technical Specifications

AD-30x2

AD-45x2

Maximum Capacity (Dry Weight)

per pocket

13.6

20.4

Tumbler Volume

per pocket

liters

311.5

413.4

Tumbler (Diameter x Depth)

76.2 x 68.5

83.2 x 76.2

Door Opening (Diameter)

54.6

68.6

Airflow (50Hz)

per pocket

cmm

10.6

12.5

Heat Rate (Gas)

per pocket

21.1

27.5

Airborne Sound Level

dB(A)

<70

Tumbler (Drive) Motor

per pocket

0.19

0.25

Blower (Fan) Motor

per pocket

0.37

Net Weight

236

290

Shipping Weight

249

318

Cabinet Width (A)

80.0

87.0

Cabinet Depth (B)

100.7

121.7

Cabinet Height (C)

198.9

205.7

Door Height (D1 / D2)

126.1 / 27.9

122.5 / 20.7

Exhaust Connection (Diameter) (E)

20.3

25.4

Gas Connection (F)

ISO 7/1

Rc 1/2

Water Connection (G)

ISO 7/1

R 3/4

Electric Connection (H)

NOTE:

The manufacturer reserves the right to make changes in specifications at any time, without notice or obligation.

Summary of Contents for AD-30x2













Search results

Summary of Contents for AD-30x2

Reviews:

Related manuals for AD-30x2

Brands by name

Popular brands

American Dryer Corp. AD-30x2, Installation & Operator'S Manual

Search results

Summary of Contents for AD-30x2

Reviews:

Related manuals for AD-30x2

Brands by name

Popular brands