©
American DJ
®
- www.americandj.com - X-Move Laser Instruction Manual Page 4
©
American DJ
®
- www.americandj.com - X-Move Laser Instruction Manual Page 3
Please carefully read and understand the instructions in this manual
thoroughly before attempting to operate this unit. These instructions
contain important safety information regarding the use and mainte-
nance of this unit. Please keep this manual with the unit, for future
reference.
X-Move Laser
General Instructions
X-Move Laser
Safety Precautions
Safety Issues:
This unit may “pop” the breaker if the maximum allotted
load of 2 amps is reached.
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture.
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to remove or break off the ground prong from the
electrical cord. This prong is used to reduce the risk of electrical
shock and fire in case of an internal short. Do not attempt to oper-
ate this unit if the power cord has been frayed or broken.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out-
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power cords should be routed so they are not likely to be walked
on, pinched by items placed upon or against them.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 18 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the unit.
C. The unit has been exposed to rain or water.
D. The unit does not appear to operate normally or exhibits a
marked change in performance.
• 4.9mW Green Laser Diode
• 6 Channel DMX Control
• 3 Operating Modes - Sound Active, Show Mode, & DMX Control
• Fan Cooled
• Digital Display for Address and Function Setting
• Multiple Patterns
• UC3 Controller (Not Included)
• 4 Preprogrammed Shows
X-Move Laser
Features
©
American DJ
®
- www.americandj.com - X-Move Laser Instruction Manual Page 5
©
American DJ
®
- www.americandj.com - X-Move Laser Instruction Manual Page 6
X-Move Laser
Warranty Registration
The X-Move Laser carries a 90 day limited warranty. Please fill out the
enclosed warranty card to validate your purchase. All returned service
items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. If the unit is under
warranty you must provide a copy of your proof of purchase invoice.
Please contact American DJ
®
customer support for a R.A. number.
DANGER
VISIBLE LASER RADIATION
-AVOID DIRECT EYE EXPOSURE
LASER DIODE
WAVELENGTH : 635~650 nm
Max Output : <4.9mW
Class IIIa Laser Product
!
!
X-Move Laser
Laser Warninig Labels
X-Move Laser
Set Up
Power Supply:
Before plugging your unit in, be sure the source volt-
age in your area matches the required voltage for your American DJ
®
X-Move Laser.™ The American DJ
®
X-Move Laser
™
is available in a
120v and 220v version. Because line voltage may vary from venue to
venue, you should be sure your unit voltage matches the wall outlet
voltage before attempting to operate you fixture. Also be sure to only
use the included I.E.C. power cable supplied with the unit, this cable
matches the voltage and current requirements of the unit.
DMX-512:
DMX is short for Digital Multiplex. This is a universal pro-
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers.
A DMX
controller sends DMX data instructions from the controller to the fix
-
ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
DMX Linking:
DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a sin-
gle controller, as long as all fixtures and the controller are DMX com
-
pliant.
To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. Therefore, the first fixture controlled by the
controller could be the last fixture in the chain. When a fixture is as-
signed a DMX address of 1, the DMX controller knows to send DATA
assigned to address 1 to that unit, no matter where it is located in the
DMX chain.
Data Cable (DMX Cable) Requirements (For
DMX and Master/Slave Operation):
The X-Move
Laser™ can be controlled via DMX-512 protocol.
The X-Move Laser™ is be a six channel DMX unit.
The DMX address is set electronically using the
controls on the rear panel of the unit. Your unit and
your DMX controller require a approved DMX-512
110 Ohm Data cable for data input and data output
(Figure 1). We recommend Accu-Cable DMX cables. If you are making
Figure 1
D A N G E R
V IS IB L E L AS E R R ADIAT IO N
-AV O ID DIR E C T E Y E E X P O S U R E
WAV E L E N G T H : 532nm/G R E E N
: 650nm/R E D
Ma x. O utput : <4. 9mW
C L AS S IIIa L AS E R P R O DU C T
C O MP L IE S W IT H C F R 1040. 10 AN D 1040. 11
L as er A pe ture
r
C AUTI O N - C LASS 3R
LASER RADIATIO N WHEN O PEN
AVO ID DIREC T EYE EXPO SURE
Americ a n DJ Supply,Inc .
4295 C ha rter Street
Los Angeles. C A 90058 USA
Ma nufa c tured:
C omplies with FDA performa nc e
sta nda rds for la ser produc ts
with the exc eption of devia -
tion pursua nt to la ser Notic e
No.50,da ted July 26,2001
LASER RADIATIO N
AVO ID DIREC T EYE EXPO SURE
C LASS 3R LASER PRO DUC T
4.9 m W m a x C W Diode
IEC /EN 60825-1,e d 1.2
C AUTION - C LASS 3R
LASER RADIATIO N WHEN
OPEN AVOID DIREC T EYE
EXPO SURE
C AUTI O N - C LASS 3R
LASER RADIATIO N WHEN O PEN
AVO ID DIREC T EYE EXPO SURE
D A N G E R
V IS IB L E L AS E R R ADIAT IO N
-AV O ID DIR E C T E Y E E X P O S U R E
WAV E L E N G T H : 532nm/G R E E N
: 650nm/R E D
Ma x. O utput : <4. 9mW
C L AS S IIIa L AS E R P R O DU C T
C O MP L IE S W IT H C F R 1040. 10 AN D 1040. 11
Q C
PAS S
Q C
PAS S
