Safety Issues:
This unit may blow a fuse if the maximum allotted
load of 3 amps is reached. If the fuse needs replacement, always
replace the fuse with same exact type that was remove, unless other-
wise instructed by an authorized American DJ
®
service technician. Use
of a different type fuse from that which is recommended may cause fire
or electric shock and will void the manufactures warranty.
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit
• Do not attempt to operate this unit if the power cord has been frayed
or broken
• Do not attempt to remove or break off the ground prong from
the electrical cord. This prong is used to reduce the risk of electrical
shock and fire in case of an internal short
• Disconnect from main power before making any type of connection
• Do not remove the cover under any conditions. There are no user
serviceable parts inside
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall
• Do not attempt to operate this unit, if it becomes damaged
• This unit is intended for indoor use only, use of this product outdoors
voids all warranties
• During long periods of non-use, disconnect the unitʼs main power
• Always mount this unit in safe and stable matter
• Power cords should be routed so they are not likely to be walked on,
pinched by items placed upon or against them.
• Cleaning -The fixture should be cleaned only as recommended by
the manufacturer. See page 7 for cleaning details
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances
(including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the unit.
C. The unit has been exposed to rain or water.
D. The unit does not appear to operate normally or exhibits a
marked change in performance.
Torch Light™
Safety Warnings
Unit Preparation:
Before beginning initial setup of your Torch Light Flame Machine, make
sure there is no evident damage caused during transportation. In the
event that the unitʼs housing or cable is damaged, do not plug the unit in
and do not attempt to use. Please contact your dealer for assistance.
1. Remove all packing materials from the Torch Light.
2. Place the Torch Light™ on a flat level surface.
3. Plug the power cord into a grounded electrical outlet with a
matching power supply.
4. Turn the power switch on rear of unit to “ON” position.
Lamps:
The positioning of the lamps is pre-set and does not require any type of
adjustment. Improperly positioned lamps will create deep spots of color
in the flame. Should the lamps need adjustment due shifting during
transit or after the replacement of a lamp, the lamps may be angled
slightly to overcome any heavy color wash. Should the lamps position-
ing become incorrectly, adjust them as follows:
1. To properly position the lamp the unit must be on. Use an insulated
screwdriver to make any adjustment to the lamps position.
2. The amber lamps should be angled to focused on the lower half of
the silk drape.
3. Position the blue lamp to shine directly in the center of silk drape.
4. All lamps will eventually fade or fail. Replacements lamps are avail-
able from your dealer.
Silk Flame:
Your silk flame has been specially designed and hand cut from the finest
silk to interact with the airflow and lights to create the illusion of a flame.
Each silk drape is applied prior to shipment and should be in the cor-
rect position. The silk drape has a life of approximately one month when
used continuously in a clean environment. Additional silk drapes may be
purchased through your dealer (part number z-torch/silk).
Torch Light™
Set-Up/Operation
©
American DJ Supply
®
- www.americandj.com - Torch Light™ Instruction Manual Page 4
©
American DJ Supply
®
- www.americandj.com - Torch Light™ Instruction Manual Page 3
