©
American DJ
®
- www.americandj.com - Profile Panel RGB™ User Manual Page 8
©
American DJ
®
- www.americandj.com - Profile Panel RGB™ User Manual Page 7
Profile Panel RGB™ Operating Instructions
Profile Panel RGB™ Operating Instructions
LED Display On/Off:
To set the LED display to turn off after 10 seconds, press the MODE
button until DS-1 is displayed, press the UP button to display DS-2.
Now the display will disappear after 10s. Press any button to turn
the display on again. Be advised though that the display will turn off
automatically after 10 seconds.
To set the display press the MODE button until DS-X is displayed. “X”
represents the number displayed.
DS-1= LCD display on at all times.
DS-2= LCD display shuts off after 10 seconds.
Operating Modes:
You can use the Profile Panel RGB™ in either a stand alone mode or
a master/slave configuration, there are 5 modes to choose from:
• Program Mode - Choose a static color, color show, color fade
show, or color cycle. The speed of the show is adjustable. You can
also have the unit strobe in this mode.
• Sound-Active mode - The unit will react to sound, chasing through
the built in programs.
• RGB mode - Choose one of the three colors to remain static or
adjust the intensity of each color to make your desired color.
• Macro Mode - Choose 1 of 32 color macros.
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller such as
as the Elation
®
Show Designer™.
Master-Slave Operation:
This function will allows you to link units together to run in a Master-
Slave mode. In Master-Slave operation one unit will act as the con-
trolling unit and the others will react to the controlling units built-in
programs. Any unit can act as a Master or as a Slave however, only
one unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the
unit. Use standard XLR microphone cables to link your units to-
gether. Remember that the Male XLR connector is the input and
the Female XLR connector is the output. The first unit in the chain
(master) will use the female XLR connector only. The last unit in
the chain will use the male XLR connector only.
2. Using the Master unit, choose your desired mode or program and
connect the “Slave” unit or units.
3. Set the “Slave” unit(s) to the DMX address mode. They will now
follow the “Master” unit.
Program Mode & Sound Active Mode:
In Program Mode you can pick your desired factory installed program;
static color, color show, color fade, or color cycle. You can apply
a strobe effect to static colors, and control the speed of the color
shows, color fade, and color cycle.
• A-01 - A-07 are static colors.
• A-08 - A-22 are color shows.
• A-23 is a color fade show.
• A-24 is a color cycle.
1. Plug the fixture in and press the MODE button until A-XX is dis-
played. You are now in AUTO mode.
2. Press the UP or DOWN buttons to find your desired effect.
3. If you have selected a static color, press the MODE button.
F-XX should be displayed. Use the UP or DOWN buttons to adjust
and select your desired Flash rate.
4. When you have chosen a color show (A-08 - A-23), press the
MODE button to adjust the speed of the show. When you press
the MODE button, the display will show “P-XX”. Press the UP or
DOWN button to adjust and set the speed. When the display
shows “P-So” your desired program is running in sound active
mode. Sound active mode only applies to color shows A-08 -
A-22, not to the color fade show (A-23).
NOTE: If you have a static color selected (A-01 - A-07), the
Program speed (P-XX) menu will not display.
5. The optional
UC3 Controller
(not included)
may be used to con-
trol different functions including blackout.
Macro Mode:
In this mode you can select 1 of 32 macros
1. Plug the fixture in and press the MODE button until either C-XX is
displayed.
2. Press the UP or DOWN buttons to find your desired macro.
