©
American DJ
®
- www.americandj.com - Gobo Scope™ Instruction Manual Page 6
©
American DJ
®
- www.americandj.com - Gobo Scope™ Instruction Manual Page 5
Gobo Scope™
Operation
Gobo Scope™
Lamp Replacement
Caution:
Always replace with the exact same type lamp, unless oth-
erwise specified by an authorized American DJ
®
technician. Replace
with anything other than the specified part can damage your unit and
will void your manufactures warranty.
Warning:
If you continue to blow either the lamp or the breaker,
STOP using the unit. Contact customer support for further instruc-
tions, you may have to return the unit for servicing. Continuing to use
the unit may cause serious damage.
Breaker Reset:
This unit is equipped with a built-in safety breaker.
This breaker is designed to close the power circuit in the event of an
internal short or power surge. This will reduce the risk of electrical
shock or fire and protect the circuitry. To reset the breaker, push the
breaker button in until you hear it “pop” back in to place. If the break-
er continues to pop, stop using the unit and contact our customer
support team, the unit may need to be returned for service.
Lamp Replacement:
Caution! Never attempt to change the lamp
while the fixture is plugged in. Always disconnect the main power
and allow the unit ample time to cool before attempting to replace the
lamp. Lamp replacement has been made simple by incorporating the
use of a flip-up front cover that is retained by a thumb screw.
1. Be sure to follow the proper handling procedures that deal with
halogen lamps.
2. Remove the thumb screw on the top of the unit.
3. After removing the thumb screw, pull off the lamp’s protective
cover.
4. Carefully remove the old lamp and discard it in the trash.
5. Replace the lamp with an exact match and reassemble in reverse
order.
Halogen Lamp Warning:
This fixture is fitted
with halogen lamps which are highly susceptible
to damage if improperly handled. Never touch the
lamps with your bare fingers as the oil from your
hands will shorten lamp life. Also, never move the
fixture until the lamps have had ample time to cool.
Remember, lamps are not covered under warranty
conditions.
Gobo Scope™
Trouble Shooting
Trouble Shooting:
Listed below are a few common problems that
you may encounter, with solutions.
No light output from the unit;
1. Be sure you have connected your unit into a wall outlet with a
matching power supply.
2. Be sure the breaker has not blown. The breaker is located on the
rear panel of the unit.
3. Remove the lamp cover and be sure the lamp is seated in its
socket properly. Occasionally lamps become loose during ship
ping be sure the lamp is push in to its socket all the way.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
General Operation:
This fixture is designed to operate as a stand alone unit, there is no
need of a controller. It has been tested and the lamp installed at the
factory there is no assembly necessary. The Gobo Scope™ is ready
to be plugged in, out of the box. There is no power switch, after plug-
ging the unit if there is no lamp output check the fuse and bulb. If
the fuse and bulb are good, please return the unit for servicing. This
fixture is designed for mobile DJ’s, clubs, bands, roller rinks and any
arena that requires a compact, light weight, easy to use fixture.
Operating Modes:
This unit comes with a speed control knob (the left knob) and a sound
sensitivity knob (the right knob). Use the sound sensitivity knob on
the back of the unit to make the unit more or less sensitive to sound.
Turning the knob clockwise will make the unit more sensitive to
sound and turning the knob counter-clockwise will make the unit less
sensitive to sound. Use the speed control knob on the back of the
unit to control the speed of the gobo/color wheel. Turning the knob
clockwise will make the gobo/color wheel turn faster and turning the
knob counter-clockwise will make the gobo/color wheel turn slower.
You can focus the unit by turning the lens on the front.
