ADJ Products, LLC - www.adj.com - Fog Fury 3000 WiFly Instruction Manual Page 10
Fog Fury 3000 WiFly
Remote Operation
Always be sure to maintain an adequate supply of ADJ Brand
Fog Juice in the fluid reservoir. Running the fog machine dry will
cause pump failure and or clogging. This is the largest cause of
failure in fog and haze machines. Only ADJ Fog Juice is recom-
mended and not all fog juice is created equal.
Remote Operation:
Start by connecting the remote to the fog
machine. Once the machine is plugged in and turned on, a red power
LED on the remote will glow indicating the unit is receiving power.
The unit has a warm up time of about eight (8) minutes. After the unit
has warmed up, a GREEN LED on the remote will light indicating the
unit is ready to emit fog. To emit fog, simply press the button on the
remote for desired length of time. If the GREEN LED is on and fog
does not come out after holding the button down for 30 seconds,
check the fluid tank and make sure you have enough fog juice.
Caution:
Before removing or replacing the remote control unit
disconnect the power supply.
ADJ Products, LLC - www.adj.com - Fog Fury 3000 WiFly Instruction Manual Page 11
Fog Fury 3000 WiFly
WiFly DMX Set Up
With this feature you are able to control the unit with DMX without the need
of XLR cables. Your DMX controller must be connected to a ADJ WiFly
TransCeiver to use this function. You are able to communicate up to 400 feet
(open line of sight)
NOTE: The “Master” setting must be set to “Off” to use WiFly DMX.
1. Set the antenna to either a up position or down position.
2. Set the Wireless address using the dipswitches on the rear of the unit.
The address must match the address set on the WiFly Transceiver.
3. After you have set the WiFly address, apply power to the ADJ WiFly
Transceiver. The fixture must be set up first before you apply power to
WiFly Transceiver.
5. If everything is set up properly and the fixture is receiving a Wireless
signal, Wireless status indicator LED will glow green.
6. The Signal strength meter will display how strong of a signal the unit is
receiving.
Note: If the sync does not work, switch the power off then on again.
This feature will let you link units to run in a master-slave mode without the
use of XLR cables.
1. Set the antenna to either a up position or down position.
2. Set the Wireless address using the dipswitches on the rear of the unit.
The addresses on each unit, master & slaves must match.
3. After you have set the WiFly address, apply power to the Master unit.
Next apply power to the slave unit(s).
4. For the Slave units, turn off the Master setting.
5. If everything is set up correctly, the Master units WiFly status LED will
glow orange, and the slave units Wireless status LED will glow green.
6. The Signal strength meter will display how strong of a signal the unit is
receiving.
NOTE: If they do not sync up master-slave, switch the Master fixtures
power switch off then on again.
Fog Fury 3000 WiFly
WiFly Master-Slave Set Up
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights. The Fog
Fury 3000 WiFly has 3 DMX channels. See page 12 for the DMX chart.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller.
2.
To run your fixture in DMX mode press the MENU button until
“A.XXX” is displayed. “XXX” represents the current displayed ad-
dress. Use the UP or DOWN buttons to select your desired DMX
address.
3. Please see page 12 for DMX values and traits.
4. After you have set your DMX address plug in the fixture via the
XLR connections to any standard DMX controller.
Fog Fury 3000 WiFly
DMX Mode
