background image

American DJ

®

  -  www.americandj.com  - Accu LED MH Instruction Manual Page 34

American DJ

®

  -  www.americandj.com  - Accu LED MH Instruction Manual Page 33

 Accu LED MH 

 

 

 

                  Operation

4.   Press UP, to select “

OFF

”, “

RUN

”, or “

AUDI

”. “

RUN

” will make the  

      unit run through a built-in program. “

AUDI

” will make the unit    

      sound active.

5.   Select a mode, and press ENTER to confirm.

6.   Press MODE/ESC if you want to return to the main menu.
7.   You may change the show or invert the pan and tilt functions           
 

 in the system menu by following the directions on page 22.

Master-Slave  Operation  (Sound  Active  or  Auto  Program): 

This function will allow you to link up to 16 units together and oper-
ate without a controller. The units can run a built-in program or run in 
sound actiive mode. In Master-Slave operation one unit will act as the 
controlling unit and the others will react to the controlling units pro-
grams. Any unit can act as a Master or as a Slave.
1.   Using standard XLR microphone cables, daisy chain your units  
 

together via the XLR connector on the rear of the units. Remem- 

 

ber the Male XLR connector is the input and the Female XLR    

 

connector is the output. The first unit in the chain (master) will use  

 

the female XLR connector only - The last unit in the chain will use  

 

the male XLR connector only. For longer cable runs we suggest a  

 

terminator at the last fixture.

2.  Access the main menu.
2.  Tap the UP button until 

PLAY

” is displayed, and Press ENTER.

3.  

Tap the UP button to choose between “

RUN

” or “

AUDI

”. “

RUN

” will  

      make the units run through a built-in program. “

AUDI

” will make  

      the units sound active.
4.   Press UP, to select “

ALON

” or “

NAST

”. Which means stand alone,  

      or master/slave mode.

5.   Select a mode, and press ENTER to confirm.

6.   Press MODE/ESC if you want to return to the main menu
7.   You may change the show or invert the pan and tilt functions           
 

 in the system menu by following the directions on page 22.

  Channel     Value 

 

       Function

       

1               0 - 255                  PAN MOVEMENT 8bit 

       2               0 - 255                       PAN FINE 16bit   
       3               0 - 255                  TILT MOVEMENT 8bit  
       4               0 - 255                       TILT FINE 16bit
       5                                   SPEED OF PAN/TILT MOVEMENT
                         0 - 255                          MAX - MIN      
       6                                              AUTO PROGRAMS

        

                                                                               

                 

                        0 - 10                            BLACKOUT
                      11 - 20                                 OPEN
                      21 - 30                           PROGRAM 1
                      31 - 40                           PROGRAM 2
                      41 - 50                           PROGRAM 3
                      51 - 60                           PROGRAM 4
                      61 - 70                           PROGRAM 5
                      71 - 80                           PROGRAM 6
                      81 - 90                           PROGRAM 7
                      91 - 100                         PROGRAM 8
                    101 - 110                         PROGRAM 9
                    111 - 120                        PROGRAM 10
                    121 - 130                        PROGRAM 11
                    131 - 140                        PROGRAM 12
                    141 - 150                        PROGRAM 13                 
                    151 - 160                        PROGRAM 14 
                    161 - 170                        PROGRAM 15
                    171 - 180                        PROGRAM 16      
                    181 - 190                        PROGRAM 17
                    191 - 200                        PROGRAM 18 
                    201 - 210                        PROGRAM 19
                    211 - 220                        PROGRAM 20                
                    221 - 230                        PROGRAM 21 
                    231 - 240                        PROGRAM 22
                    241 - 250                        PROGRAM 23      
                    251 - 255                        PROGRAM 24

  Accu LED MH  

 

 

 

                 DMX Traits

Summary of Contents for Accu LED MH





















Reviews: