background image

(36) PHONO / AUX SELECTOR SWITCH -

 Changes phono to an extra line; allows the DJ to use a CD player 

or other input device in the same line as the phono line. When using a turntable select PHONO, and when 

using other input devices select AUX. PHONO/AUX lines can be used with LINES 1 and 2. The PHONO /AUX 

SELECTOR SWITCH gives the DJ the possibilities of 2 extra input lines.

(37) CHANNEL 1 INPUT JACKS -

 Connect CD players, tape decks, DAT machines, and all other non-magnetic 

equipment to the line level inputs. Line level musical instruments with stereo outputs such as Rhythm Machines 

or Samplers should also be connected to LINE inputs. When connecting turntables with MM pickup cartridge 

use  the  Phono  inputs.   The  RCA  input  jacks  are  color  code,  the  red  jack  reprsents  the  right  channel  and 

the white jack represents the left channel. Be sure your turntable are connected to the AUX/PHONO jacks, 

you must also be sure that the AUX/PHONO (38) switch is set to the "PHONO" position. Never plus in a line 

level input in to these jacks while the AUX/PHONO (38) switch is set to the "PHONO poistion, this may cause 

damage to your mixer and/or audio system. When the AUX/PHONO (38) switch is set to the "AUX" position, 

the jacks will only accept a line level input.

(38) MIC 2 INPUT JACK -

 Connect your microphone with 1/4 inch (6.3mm) jack plug here. The signals may be 

controlled by the MIC 1 VOLUME KNOB (18). BASS & TREBLE for MIC 1 can be adjusted by the  MIC BASS 

CONTROL KNOB (19) and the MIC TREBLE CONTROL KNOB (19). MIC 2 volume can be adjusted by the 

MIC 2 VOLUME KNOB (18). There is also a XLR-plug for MIC 1 (15) on the front panel.

Replacing the Crossfader

1.   Disconnect the mixers main power supply

2.   Using a number two Phillips screw driver, unscrew the each of the stainless steel retain screws 

   that hold the crossfader in place.

3.    Gently remove the crossfader from its seated position. You may need to wiggle the crossfader 

    slightly to remove it.

4.    After removing the crossfader, disconnect the ribbon cable that attaches the crossfader to the 

   PC board. Grasp the crossfader by its base and pull the ribbon cable by its connector not the 

   actual cables. The connector is desired to only fit one way, so don't worry about the connectors 

   orientation. 

5.    Connect the new crossfader to the ribbon cable and replace in reverse order.

Rear Panel Cont.

©

American DJ Audio

®

 - www.americandj.com - Q-2422/SX™ User Instructions page 9

Summary of Contents for Q-2422 - AUTRE











Reviews: