background image

©

American DJ Audio

®

 - www.americandj.com - Q-2422/SX™ User Instructions page 10

Warranty & Service:

The Q-2422/SX™ has a 2-year limited warranty.  Please mail in warranty card as soon as possible to validate 

your warranty.

Technical Specifications - Model Q-2221/X

Model:  

 

Q-2422/SX™, 2 Channel Mixer

Power supply:

  

AC 115/230V, 50/60Hz switchable

Dimensions:

   

19" W x 7" D x 2.25" H / 482x 176x 65mm

Weight:

  

 

8.5 lbs. / 3.8 kg

Crossfader:   

FF-Plus - 

Optical detecting fader start control - Low grounding impedance crossfader

Power Consumption:

 5W typical, 7W w/ full headphone output

Headphone impedance:

 16 Ohms

Input Sensitivity (Level/Impedence):

Line: 

-14dBV (200mV) 12K Ohm +/- 2dB

Microphone:

 -49 dBV (3.6mV0 / 3K Ohms +/- 3 dB

Phono:

 -48dBV (4mV) 47K Ohms +/- 3dB

Aux:

 -14 dBV (200mV) / 47K Ohms +/- 2dB

Output Sensitivity (Level/Impedence):

Rec Out (RCA): 

-10dBV (316mV) / 2.2K Ohms +/- 2dB

Master Out (RCA):

 0dBV (1V) / 610 Ohms +/-2dB

Phones (Load+32Ohms): 

-8dBV (0.4V) /33 Oms +/-2dB

Maximum Output (Load + 47K, THD = 5%)

Rec: 

< 18dBV (8V)

Master (RCA):

 < 18dBV (8V)

Blanced (XLR):

 < 18dBV (8V)

Channel Balance: 

Within 3dB

Frequency Response:

• Line:

 20Hz - 20KHz, ± 1dB 

• Phono: 

20Hz - 20KHz, ± 1.5dB (RIAA) 

• Aux: 

20Hz - 20KHz, ± 1dB

• Microphone:

 20Hz - 20KHz, +1,-3dB

THD - Total Harmonic Distortion (1Khz, 0dBV Output):

Master Output (Load = 47K Ohms):

 Less than 0.2%

Phono:

 

(Load = 32K Ohms):

 Less than 0.5%

Channel Equalizer:

Bass =  

+12 ± 1dB, -22 ± 2 dB at 70KHz

 / Mid = 

+12 ± 1dB, -17 ± 2 dB at 1KHz

  / Treble = 

+13 ± 

1dB, -27 ± 2 dB at 13KHz

Microphone Equalizer:

Bass = 

+12 ± 1dB, -12 ± 1 dB at 100KHz 

/ Treble = 

+12 ± 1dB, -12 ± 1 dB at 10KHz

Summary of Contents for Q-2422 - AUTRE











Reviews: