background image

jack represents the right channel input and the white represents the left channel input.

27. CHANNEL 3: LINE 3 AUX INPUT JACKS - 

DO NOT CONNECT TURNTABLES TO THESE JACKS!  

These Jacks are used for line level inputs. Connect CD players or Tape Decks to LINE inputs. Line level 
musical instruments with stereo outputs such as Rhythm Machines or Samplers should also be con-
nected to LINE inputs. Turntables should only be connected to “Phono” inputs. The red colored RCA 
jack represents the right channel input and the white represents the left channel input.

28. REC OUT

 - This is a low current unbalanced output source designed for various tape and CD 

recorders. The Record Out (REC OUT) level is dictated by the 

CHANNEL FADER LEVEL (9)

, it is not 

influenced by the 

MASTER VOLUME CONTROL (4)

.

29. RCA MASTER OUTPUTS -

 The Master Output includes a pair of RCA 

UNBALANCED JACKS (24).

 

The RCA jacks send a low current unbalanced output signal. 

30.  BALANCED  XLR  MASTER  OUTPUTS  - 

The  Master  Output  includes  a  pair  XLR  Balanced 

JACKS as well as a pair 

RCA UNBALANCED JACKS (29)

. The 3-pin XLR jacks send a high current 

balanced output signal. These jacks should be used when you will be driving an amp or other audio 
equipment with a balanced input, or whenever you will be running a signal line greater than 15 feet. 
Always, use these jacks whenever possible.

31.  9V AC INPUT - 

Connect the included power supply to this input, or any other 9v power adapter.

32. MAIN POWER SWITCH -

 This is the main power ON/OFF button. An L.E.D. located on the front 

of the mixer will glow green when the power is ON. Before main power is applied, be sure you have 
made all connections to the mixer. Also be sure your amplifier(s) is(are) tuned off. Remember to avoid 
damaging pops, the mixer should be powered on first and turned off last.

 Q-D6 SRS™   

 

  

  

 

 

      

                   Controls and Features Cont.

©

American Audio

®

   -   www.americanaudio.us   -   Q-D6 SRS™ Instruction Manual Page 12

33

34

33. HEADPHONE OUTPUT JACK -

 This jack is used to connect your headphones to the mixer allow-

ing you to monitor the cue source. Use headphones only rated at 8 ohms to 32 ohms. Most DJ head-
phones are rated at 16 ohm, these are highly recommended. Always be sure the CUE LEVEL VOLUME 
(5) is set to minimum before you put the headphones on.

34. MICROPHONE CONNECTOR -

 This jack is used to a connect a microphone to the mixer. Connect 

you microphone via 1/4 inch (6.3mm) jack. The signal volume will be controlled by the 

MIC LEVEL (17)

The bass and treble levels can also be adjusted by the built-in 

MICROPHONE EQ (17).

Summary of Contents for 640282055895




















Reviews: