background image

 

PN 05606

 

04/2020

 

All fire extinguishers shall be installed, inspected, and maintained in accordance with the National Fire 

Protection Association standard titled "Portable Fire Extinguishers", NFPA 10, and the requirements of local 

authorities having jurisdiction.

 

When  maintenance  is  indicated,  it  shall  be  performed  by  trained  persons  having  proper  equipment.  Fire 

extinguishers  are  pressure  vessels  and  must  be  treated  with  respect  and  handled  with  care.  They  are 

mechanical devices and require periodic maintenance to be sure that they are ready to operate properly and 

safely. Amerex strongly recommends that the maintenance of portable fire extinguishers be done by a trained 

professional –

 

your local authorized Amerex Distributor.

 

Amerex  Corporation  makes  original  factory  parts  available  to  insure  proper  maintenance  –

 

USE  OF 

SUBSTITUTE  PARTS  RELEASES  AMEREX  OF  ITS  WARRANTY  OBLIGATIONS.  Amerex  parts  have 

machined surfaces and threads that are manufactured to exacting tolerances. O

-

rings, hoses, nozzles, and all 

metal  parts  meet  precise  specifications  and  are  subjected  to  multiple  in

-

house  inspections  and  tests  for 

acceptability.  There  are  substitute  parts  available  that  may  be  incorrectly  labeled  as  UL  component  parts, 

some are advertised as Amerex type. None of these meet UL requirements, and all of them void the Amerex 

extinguisher warranty. DO NOT SUBSTITUTE.

 

RECHARGE FIRE EXTINGUISHERS IMMEDIATELY AFTER ANY USE

 

OWNER

S SERVICE MANUAL

 

INSTALLATION, OPERATING & SERVICING INSTRUCTIONS

 

MANUAL PN 05606

 

WHEELED STORED

-

PRESSURE HALON 1211 EXTINGUISHERS  

 

MODELS 600, 695

 

AMEREX  CORPORATION  DOES  NOT  SERVICE,  MAINTAIN,  OR  RECHARGE  FIRE  EXTINGUISHERS. 

THIS  MANUAL  IS  PUBLISHED  AS  A  GUIDE  TO  ASSIST  QUALIFIED  SERVICE  PERSONNEL  IN  THE 

INSPECTION,  MAINTENANCE,  AND  RECHARGE  OF  AMEREX  FIRE  EXTINGUISHERS  ONLY.  NO 

INSTRUCTION  MANUAL  CAN  ANTICIPATE  ALL  POSSIBLE  MALFUNCTIONS  THAT  MAY  BE 

ENCOUNTERED IN THE SERVICE OF FIRE EXTINGUISHERS. DUE TO THE POSSIBILITY THAT PRIOR 

SERVICE  PERFORMED  ON  THIS  EQUIPMENT  MAY  HAVE  BEEN  IMPROPERLY  DONE,  IT  IS 

EXTREMELY  IMPORTANT  THAT  ALL  WARNINGS,  CAUTIONS,  AND  NOTES  IN  THIS  MANUAL  BE 

CAREFULLY  OBSERVED.  FAILURE  TO  HEED  THESE  INSTRUCTIONS  COULD  RESULT  IN  SERIOUS 

INJURY. AMEREX ASSUMES NO LIABILITY FOR SERVICE, MAINTENANCE, OR RECHARGE OF FIRE 

EXTINGUISHERS BY PUBLISHING THIS MANUAL.

 

AMEREX CORPORATION –

 

P.O. BOX 81 –

 

TRUSSVILLE, ALABAMA  35173

-

0081

 

Phone:  205/655

-

3271     Fax:  800/654

-

5980

 

e

-

mail:  sales@amerex

-

fire.com      Web Page:  http://www.amerex

-

fire.com

 

REFERENCES IN THIS MAUNUAL:                                                        

NFPA 10 

Portable Fire Extinguishers  

JJJJJJJJJJJJJJJJJJJJJJJJJJJJJJJJJJJJJJJJJJJJ            

                                                          

 

CGA C

-

Methods for Pressure Testing Compressed Gas 

Cylinders

 

CGA C

-

Standard for Visual Inspection of Steel 

Compressed Gas Cylinders. 

 

 

AVAILABLE FROM:                                                                             

National Fire Protection Association, 1 Batterymarch Park, 

Quincy, MA 02169

-

7471 

 

Compressed Gas Association, 14501 George Carter Way, 

Chantilly, VA 20151

-

2923

 

Compressed Gas Association, 14501 George Carter Way, 

Chantilly, VA 20151

-

2923

 

FOR REPLACEMENT PARTS SEE THE AMEREX PORTABLE AND WHEELED 

PARTS BOOK PN 27277 AVAILABLE AT http://www.amerex

-

fire.com UNDER 

MANUALS OF THE RESOURCE SELECTION. 

 

 

Summary of Contents for 600









Reviews: