background image

4

EN

•  The product shall be maintained by a qualified person.

•  Do not exceed rated capacity. 

•  Use only on a hard, level surface.

•  Ensure load is secured to the product.

•  No alterations shall be made to this product.

•  Only attachments and/or adapters supplied by or approved by the 

manufacturer shall be used.

•  Release load-locking devices (if employed) slowly and carefully.

•  Center load on saddle (lift pad) prior to lifting.

•  Do not move or dolly the vehicle while it is on the jack.

•  Before using the product with the vehicle, always engage the vehicle 

parking brakes and block the wheels.

SAVE THESE INSTRUCTIONS

Intended Use

•  This product is designed to lift (not support), rated capacity loads 

consisting of one end of a vehicle. Immediately after lifting, the load 
must be supported by a pair of appropriately rated jack stands. Wood 
blocks, bricks, or concrete blocks are not acceptable substitutes for 
jack stands.

•  This product is intended for private use only. It is not intended for 

commercial use in garages or repair shops. 

•  This product is intended to be used in dry indoor and outdoor areas.

•  No liability will be accepted for damages resulting from improper use 

or non-compliance with these instructions.

Summary of Contents for B07XFSSFDS

















Reviews: