Amana Room Air Conditioner & Heat Pump Use And Care Manual Download Page 17

17

BEFORE CALLING SERVICE

PROBLEM 

POSSIBLE CAUSE 

SUGGESTED REMEDY 

UNIT WILL NOT RUN 

No power to unit 

Push reset button on power cord. 
Set Fan Control to position other than OFF. 
Make sure plug is firmly seated in outlet. 
Check for blown fuses, tripped circuit breakers. 

LITTLE OR NO COOLING 
LITTLE OR NO HEATING 

(fan 

and

 compressor run) 

Fresh air/exhaust damper open 
Obstructed indoor or outdoor airflow 
Dirty air filters 
Unit undersized for application 

Set vent to CLOSED. 
Remove obstruction from indoor grille or outdoor louvers. 
Dirty air filter. Clean or replace, as needed. 
Check with dealer to determine proper capacity unit for application. 

LITTLE OR NO COOLING 

LITTLE OR NO HEATING 

(only fan runs) 

Temperature Control not set properly 

For cooling, turn Temperature Control to cooler setting. 

For heating, turn Temperature Control to warmer setting. 

NOISY UNIT 

Loose front on mounting assembly 

Weak building construction 

Water hitting fan blade 

Unit oversized for application: 

compressor cycles on and off frequently 

Tighten any loose parts. 

Provide additional support for unit. 

Normal in high humidity. Stop noise by removing drain plug or 

adding condensate drain cup. 
Check with dealer to determine proper capacity unit for application. 

MOUNTING SUPPORT NOT 

INSTALLED 

Storm window frame installed in window  Some models require removal of storm window frame before 

installation. 

FROST ON INDOOR COIL 

Dirty air filter 

Normal for low outdoor temperatures 

Clean air filter by vacuuming or washing with water and mild soap. 

Turning Temperature Control to warmer setting reduces occurrence 

and duration of frost. 

FROST ON OUTDOOR COIL 

(heat pump models only) 

Normal for outdoor temperatures at or 

below 45°F 

Call for service 

only

 if unit does not heat room and you have 

checked all problems and remedies listed under LITTLE OR NO 

HEATING. 

ODORS IN COOLING 

Mold, mildew, or algae formation on wet 

surfaces 

To reduce algae growth, use algaecide tablet in base pan; remove 

drain plug; add condensate drain cup and hose. Thoroughly clean 

unit. 

ODORS IN HEATING 

Normal for first time electric heater is 

used each season 

Caused by dust accumulation during unused months. 
Odor dissipates quickly with heater use. 

 

The following is a list of problems that are sometimes encountered when using a room air conditioner.  Possible cause and

suggested remedies are given for each problem.
If the problem cannot be fixed using the suggested remedies, see 

WHEN SERVICE IS REQUIRED

 section.

WARNING

Summary of Contents for Room Air Conditioner & Heat Pump





















Reviews: