manualshive.com logo in svg

Amana RCS10A, Service Manual, Page: 31 / 44

Share
Download
Amana RCS10A Service Manual Download Page 31

5-13

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1. Fuse blows.

Continuity.

No continuity.

Continuity.

Shorted contact at
the primary switch.

Replace fuse,
primary, monitor,
secondary
switches, and
RELAY(RY2) of
P.C.B Assembly.

No continuity.

Malfunction of the
monitor switch.

Replace fuse,
primary, monitor,
secondary
switches, and
RELAY(RY2) of
P.C.B Assembly.

Check continuity
of monitor
switch (with
door closed).

Check continuity
of primary
switch (with
door opened).

Replace fuse

Continuity.

Malfunction of
secondary switch.

Replace fuse,
primary, monitor,
secondary
switches, and
RELAY(RY2) of
P.C.B Assembly.

No continuity.

Check continuity
of secondary
switch (with
door opened).

2. Fuse does not

blow.

No continuity.

Continuity.

No continuity.

Defective power
supply cord.

Replace power
supply cord.

Defective
thermostat.

Replace
thermostat.

Check continuity
of thermostat.

Check continuity
of power  supply
cord.

(TROUBLE 2) Oven does not operate at all, Display window does not display any figures, 

and no input is accepted.

NOTE : All these switches must be replaced at the same time. Refer to page 5-7, 5-8

Normal.

Normal.

Abnormal.

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Set is good condition
(defective fuse only)

Fuse blows again

Defective high volt-
age transformer.

Replace high volt-
age transformer.

Disconnect one
side of the wire
lead connected
from transformer
to the high voltage
capacitor and
operate the unit.

Measure to
resistance high
voltage capacitor
(refer to page 5-9)

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1. Fuse blows.

Continuity.

No continuity.

Continuity.

Shorted contact at
the primary switch.

Replace fuse,
primary, monitor,
secondary
switches, and
RELAY(RY3 ) 
of P.C.B Assembly.

No continuity.

Malfunction of the
monitor switch.

Replace fuse,
primary, monitor,
secondary
switches, and
RELAY(RY3) 

Check continuity
of monitor
switch (with
door closed).

Check continuity
of primary
switch (with
door opened).

Replace fuse

Continuity.

Malfunction of
secondary switch.

Replace fuse,
primary, monitor,
secondary
switches, and
RELAY(RY3) 
of P.C.B Assembly.

No continuity.

Check continuity
of secondary
switch (with
door opened).

2. Fuse does not

blow.

No continuity.

Continuity.

No continuity.

Defective power
supply cord.

Replace power
supply cord.

Defective
thermostat.

Replace
thermostat.

Check continuity
of thermostat.

Check continuity
of power  supply
cord.

(TROUBLE 2) Oven does not operate at all, Display window does not display any figures, 

and no input is accepted.

NOTE : All these switches must be replaced at the same time. Refer to page 5-7, 5-8

Normal.

Normal.

Abnormal.

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Set is good condition
(defective fuse only)

Fuse blows again

Defective high volt-
age transformer.

Replace high volt-
age transformer.

Disconnect one
side of the wire
lead connected
from transformer
to the high voltage
capacitor and
operate the unit.

Measure to
resistance high
voltage capacitor
(refer to page 5-9)

1. Fuse blows.

Continuity.

No continuity.

Continuity.

Shorted contact at
the primary switch.

Replace fuse,
primary, monitor,
secondary
switches, and

No continuity.

Malfunction of the
monitor switch.

Replace fuse,
primary, monitor,
secondary
switches, and

Check continuity
of monitor
switch (with
door closed).

Check continuity
of primary
switch (with
door opened).

Replace fuse

Continuity.

Malfunction of
secondary switch.

Replace fuse,
primary, monitor,
secondary
switches, and

No continuity.

Check continuity
of secondary
switch (with
door opened).

2. Fuse does not

blow.

No continuity.

Continuity.

No continuity.

Defective power
supply cord.

Replace power
supply cord.

Defective
thermostat.

Replace
thermostat.

Check continuity
of thermostat.

Check continuity
of power  supply
cord.

Oven does not operate at all, Display window does not display any figures, 

and no input is accepted.

Normal.

Normal.

Abnormal.

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Set is good condition
(defective fuse only)

Fuse blows again

Defective high volt-
age transformer.

Replace high volt-
age transformer.

Disconnect one
side of the wire
lead connected
from transformer
to the high voltage
capacitor and
operate the unit.

Measure to
resistance high
voltage capacitor
(refer to page 5-9)

1. Fuse blows.

Continuity.

No continuity.

Continuity.

Shorted contact at
the primary switch.

Replace fuse,
primary, monitor,
secondary
switches, and

No continuity.

Malfunction of the
monitor switch.

Replace fuse,
primary, monitor,
secondary
switches, and

Check continuity
of monitor
switch (with
door closed).

Check continuity
of primary
switch (with
door opened).

Replace fuse

Continuity.

Malfunction of
secondary switch.

Replace fuse,
primary, monitor,
secondary
switches, and

No continuity.

Check continuity
of secondary
switch (with
door opened).

2. Fuse does not

blow.

No continuity.

Continuity.

No continuity.

Defective power
supply cord.

Replace power
supply cord.

Defective
thermostat.

Replace
thermostat.

Check continuity
of thermostat.

Check continuity
of power  supply
cord.

Normal.

Normal.

Abnormal.

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Set is good condition
(defective fuse only)

Fuse blows again

Defective high volt-
age transformer.

Replace high volt-
age transformer.

Disconnect one
side of the wire
lead connected
from transformer
to the high voltage
capacitor and
operate the unit.

Measure to
resistance high
voltage capacitor
(refer to page 5-9)

1. Fuse blows.

Continuity.

No continuity.

Continuity.

Shorted contact at
the primary switch.

Replace fuse,
primary, monitor,
secondary
switches, and

No continuity.

Malfunction of the
monitor switch.

Replace fuse,
primary, monitor,
secondary
switches, and

of P.C.B Assembly.

Check continuity
of monitor
switch (with
door closed).

Check continuity
of primary
switch (with
door opened).

Replace fuse

Continuity.

Malfunction of
secondary switch.

Replace fuse,
primary, monitor,
secondary
switches, and

No continuity.

Check continuity
of secondary
switch (with
door opened).

2. Fuse does not

blow.

No continuity.

Continuity.

No continuity.

Defective power
supply cord.

Replace power
supply cord.

Defective
thermostat.

Replace
thermostat.

Check continuity
of thermostat.

Check continuity
of power  supply
cord.

Normal.

Normal.

Abnormal.

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Set is good condition
(defective fuse only)

Fuse blows again

Defective high volt-
age transformer.

Replace high volt-
age transformer.

Disconnect one
side of the wire
lead connected
from transformer
to the high voltage
capacitor and
operate the unit.

Measure to
resistance high
voltage capacitor
(refer to page 5-9)

Summary of Contents for RCS10A













































Reviews:

No comments