DIAGNOSTICS & TROUBLESHOOTING
Amana Compact Washer
n
2-3
For Service Technician Use Only
Manual Test Mode
Spin Test
Press
POWER
to turn on the washer.
Press and hold “
+
” while pressing
START
three times. A tone
will sound for 1 second to indicate successful entering of the
Spin Test.
The display will indicate “
3
” if there is no water in the tub,
“
4
” if there is water in the tub. The “Normal” indicator will be
flashing. When water in the tub reaches the “RESET” level,
the washer will start to spin (continuous for 1 minute, off for 1
minute). The washer will then turn off.
If the lid is opened during the spin, the display will indicate
“
E4
” and the washer will stop spinning. If the lid is closed
again, the washer will resume spinning. If the tub switch
detects an unbalance during the spin, “
E3
” will show on the
display and the motor will stop.
Press
POWER
to clear the error and exit the test.
Lid Switch Test
Press
POWER
to turn on the washer.
Press and hold
CYCLE
while pressing
START
three times. A tone
will sound for 1 second to indicate successful entering of the
Lid Switch Test.
The “
Normal
” indicator will be lit, and the washer tub will
begin to rotate clockwise. If the lid is opened, the tub will stop;
if it is closed again, the tub will resume rotation. The tub will
not rotate if it contains water.
Press
POWER
to exit the test.
Press CYCLE Until Following Indicator is Lit:
Press and Hold START to Initiate:
7-Segment Display Shows:
Normal
Clockwise rotation of the motor
Model Number
Delicate
Counter-clockwise rotation of the motor
Software version number
Heavy Duty
Activation of the Drain Pump
Voltage/frequency
Rinse
Activation of the Cold Water Valve
Size of tub/up drain
Spin
Activation of the Hot Water Valve
Min-Max water level frequency
Clean Washer
Activation of the lid lock solenoid (lid
will lock) (Release of START will unlock
the lid)
Washer serial number
Manual Load Test Chart
Press
POWER
to exit the test.
UI/LED Test
Press
POWER
to turn on the washer.
Press and hold
LOAD
while pressing
START
three times. A tone
will sound for 1 second to indicate successful entering of the
UI/LED Test. The display will indicate “
8.8
.” and all indicators
will be off.
Press “
–
”. The Control Lock and Lid Lock indicators will be lit.
Press “
–
” again. The Control Lock and Lid Lock indicators will
turn off.
Press
CYCLE
. All of the Cycle indicators will be lit. Press
CYCLE
again. The Cycle indicators will turn off.
Press “
+
”. The 7-segment display showing “
8.8
.” will turn off.
Press “
+
” again. The 7-segment display will turn on.
Press
LOAD
. All of the Load indicators will be lit. Press
LOAD
again. The Load indicators will turn off.
Press
TEMP
. All of the Temp indicators will be lit. Press
TEMP
again. The Temp indicators will turn off.
Press
POWER
to exit the test.
Manual Load Test
Refer to “Manual Load Test Chart” below.
NOTE:
The tub must be empty of clothes and water before
running this test.
To activate Manual Load Test, press and hold
CYCLE
and turn
on the washer. While continuing to press and hold
CYCLE
,
press
START
three times. A tone will sound for 1 second to
indicate successful entering of the Manual Load Test. The
“Control Lock” indicator will be lit.
Instructions:
Press
CYCLE
to select the Load to test. Press
and hold
START
to apply power to the Load. The Load will be
powered as long as the
START
button is pressed. Release the
START
button to turn off power to the Load.
NOTE:
The speaker will beep on and off as long as the
START
button is depressed.
