background image

Installation Instructions for

 *CVC96*BB & *MVC96*BB Two-Stage Gas Furnace

(Type FSP CATEGORY IV Direct

or Non Direct Vent Air Furnace)

(Type FSP CATÉGORIE IV Direct

ou four á air soufflé non direct)

IOG-2015E

7/2020

19001 Kermier Rd., Waller, TX 77484

www.goodmanmfg.com•www.amana-hac.com

© 2018-2020 Goodman Manufacturing Company, L.P. 

 is a registered trademark of Maytag Corporation or its related companies and is used under license. All rights 

reserved.

As a professional installer you have an obligation to know 

the product better than the customer. This includes all 

safety precautions and related items.

Prior to actual installation, thoroughly familiarize yourself 

with this Instruction Manual. Pay special attention to all 

safety warnings. Often during installation or repair it is 

possible to place yourself in a position which is more 

hazardous than when the unit is in operation.

Remember, it is your responsibility to install the product 

safely and to know it well enough to be able to instruct a 

customer in its safe use.

Safety is a matter of common sense...a matter of thinking 

before acting. Most dealers have a list of specific good 

safety practices...follow them.

The precautions listed in this Installation Manual are 

intended as supplemental to existing practices.   However, 

if there is a direct conflict between existing practices and 

the content of this manual, the precautions listed herein 

take precedence.

 RECOGNIZE THIS SYMBOL AS A 

SAFETY PRECAUTION. 

*

NOTE:  Please contact your distributor or our website 

for  the  applicable  Specification  Sheet  referred  to  in  this 

manual.

Installer: 

Affix all manuals

adjacent to the unit.

These furnaces comply with requirements embodied 

in the American National Standard/National Standard 

of Canada ANSI Z21.47•CSA-2.3 Gas Fired Central 

Furnaces. 

O

NLY

 

PERSONNEL

 

THAT

 

HAVE

 

BEEN

 

TRAINED

 

TO

 

INSTALL

ADJUST

SERVICE

 

OR

 

REPAIR

 (

HEREINAFTER

, “

SERVICE

”) 

THE

 

EQUIPMENT

 

SPECIFIED

 

IN

 

THIS

 

MANUAL

 

SHOULD

 

SERVICE

 

THE

 

EQUIPMENT

. T

HE

 

MANUFACTURER

 

WILL

 

NOT

 

BE

 

RESPONSIBLE

 

FOR

 

ANY

 

INJURY

 

OR

 

PROPERTY

 

DAMAGE

 

ARISING

 

FROM

 

IMPROPER

 

SERVICE

 

OR

 

SERVICE

 

PROCEDURES

.  I

F

 

YOU

 

SERVICE

 

THIS

 

UNIT

YOU

 

ASSUME

 

RESPONSIBILITY

 

FOR

 

ANY

 

INJURY

 

OR

 

PROPERTY

 

DAMAGE

 

WHICH

 

MAY

 

RESULT

.  I

N

 

ADDITION

IN

 

JURISDICTIONS

 

THAT

 

REQUIRE

 

ONE

 

OR

 

MORE

 

LICENSES

 

TO

 

SERVICE

 

THE

 

EQUIPMENT

 

SPECIFIED

 

IN

 

THIS

 

MANUAL

ONLY

 

LICENSED

 

PERSONNEL

 

SHOULD

 

SERVICE

 

THE

 

EQUIPMENT

.  I

MPROPER

 

INSTALLATION

ADJUSTMENT

SERVICING

 

OR

 

REPAIR

 

OF

 

THE

 

EQUIPMENT

 

SPECIFIED

 

IN

 

THIS

 

MANUAL

OR

 

ATTEMPTING

 

TO

 

INSTALL

ADJUST

SERVICE

 

OR

 

REPAIR

 

THE

 

EQUIPMENT

 

SPECIFIED

 

IN

 

THIS

 

MANUAL

 

WITHOUT

 

PROPER

 

TRAINING

 

MAY

 

RESULT

 

IN

 

PRODUCT

 

DAMAGE

PROPERTY

 

DAMAGE

PERSONAL

 

INJURY

 

OR

 

DEATH

.

WARNING

PROP 65 WARNING

 

FOR CALIFORNIA CONSUMERS

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov

0140M00517-A

Summary of Contents for CVC96 BB Series





















































Reviews: