background image

CONDENSING UNIT

Air Conditioning 

Installation & Service Reference

 is a registered trademark of Maytag Corporation or its related 

companies and is used under license. All rights reserved.

© 2021-2022  

Daikin Comfort Technologies Manufacturing, L.P. 

19001 Kermier Rd. Waller, TX 77484

www.goodmanmfg.com -or- www.amana-hac.com

P/N: IOG-4036B 

Date:  December 2022

IMPORTANT SAFETY INSTRUCTIONS

The following symbols and labels are used throughout this 

manual to indicate immediate or potential safety hazards. 

It is the owner’s and installer’s responsibility to read 

and comply with all safety information and instructions 

accompanying these symbols. Failure to heed safety 

information increases the risk of personal injury, property 

damage, and/or product damage.

WARNING

High Voltage!

Disconnect all power before servicing or 

installing this unit.  Multiple power sources may 

be present.  Failure to do so may cause property 

damage, personal injury or death.

ONLY PERSONNEL THAT HAVE BEEN TRAINED TO INSTALL, 

ADJUST, SERVICE, MAINTENANCE OR REPAIR 

 

(HEREINAFTER, “SERVICE”) THE EQUIPMENT SPECIFIED IN 

THIS MANUAL SHOULD  

SERVICE THE EQUIPMENT.  THE MANUFACTURER WILL 

NOT BE RESPONSIBLE FOR ANY INJURY OR PROPERTY 

DAMAGE ARISING FROM IMPROPER SERVICE OR SERVICE 

PROCEDURES.  IF YOU SERVICE THIS UNIT, YOU ASSUME 

RESPONSIBILITY FOR ANY INJURY OR PROPERTY 

 

DAMAGE WHICH MAY RESULT.  IN ADDITION, IN 

 

JURISDICTIONS THAT REQUIRE ONE OR MORE LICENSES 

TO SERVICE THE EQUIPMENT SPECIFIED IN THIS 

 

MANUAL, ONLY LICENSED PERSONNEL SHOULD SERVICE 

THE EQUIPMENT.  

 

IMPROPER INSTALLATION, ADJUSTMENT, SERVICING, 

MAINTENANCE OR REPAIR OF THE EQUIPMENT SPECIFIED 

IN THIS MANUAL, OR ATTEMPTING TO INSTALL, ADJUST, 

SERVICE OR REPAIR THE EQUIPMENT SPECIFIED IN THIS 

MANUAL WITHOUT PROPER TRAINING MAY RESULT IN 

PRODUCT DAMAGE, PROPERTY DAMAGE, PERSONAL 

 

INJURY OR DEATH.

WARNING

WARNING

DO NOT BYPASS SAFETY DEVICES

SHIPPING INSPECTION

Always keep the unit upright; laying the unit on its side 

or top may cause equipment damage. Shipping damage, 

and subsequent investigation is the responsibility of 

the carrier. Verify the model number, specifications, 

electrical characteristics, and accessories are correct 

prior to installation. The distributor or manufacturer will not 

accept claims from dealers for transportation damage or 

installation of incorrectly shipped units.  

CODES & REGULATIONS

This product is designed and manufactured to comply 

with national codes. Installation in accordance with such 

codes and/or prevailing local codes/regulations is the 

responsibility of the installer. The manufacturer assumes 

no responsibility for equipment installed in violation of any 

codes or regulations. Rated performance is achieved after 

20 hours of operation.

Rated performance is delivered at the specified airflow. 

See outdoor unit specification sheet for split system models 

or product specification sheet for packaged and light 

commercial models. Specification sheets can be found at 

www.goodmanmfg.com for Goodman® brand products or 

www.amana-hac.com for Amana® brand products. Within 

either website, please select the residential or commercial 

products menu and then select the submenu for the type 

of product to be installed, such as air conditioners or heat 

pumps, to access a list of product pages that each contain 

links to that model’s specification sheet.

The United States Environmental Protection Agency 

(EPA) has issued various regulations regarding the 

introduction and disposal of refrigerants. Failure to 

follow these regulations may harm the environment 

and can lead to the imposition of substantial fines.

 

Should you have any questions please contact the local 

office of the EPA.

If replacing a condensing unit or air handler, the system 

must be manufacturer approved and Air Conditioning, 

Heating and Refrigeration Institute (AHRI) matched.  

NOTE: Installation of unmatched systems is 

strongly discouraged.

Summary of Contents for ASXH3 Series

















Reviews: