Amana ARPT**14 Series Installation & Operating Instructions Manual Download Page 24

24

SPLIT SYSTEMS

AIR CONDITIONING AND HEAT PUMP HOMEOWNER’S

 

ROUTINE MAINTENANCE RECOMMENDATIONS

We strongly recommend a bi-annual maintenance checkup be performed

before the heating and cooling seasons begin by a qualified servicer.

Replace or Clean Filter

IMPORTANT NOTE: 

Never operate unit without a filter in-

stalled as dust and lint will build up on internal parts resulting
in loss of efficiency, equipment damage and possible fire.

An indoor air filter must be used with your comfort system. A
properly maintained filter will keep the indoor coil of your com-
fort system clean. A dirty coil could cause poor operation
and/or severe equipment damage.

Your air filter or filters could be located in your furnace, in a
blower unit, or in “filter grilles” in your ceiling or walls. The
installer of your air conditioner or heat pump can tell you where
your filter(s) are, and how to clean or replace them.

Check your filter(s) at least once a month. When they are
dirty, replace or clean as required. Disposable type filters
should be replaced. Reusable type filters may be cleaned.

You may want to ask your dealer about high efficiency filters.
High efficiency filters are available in both electronic and non-
electronic types. These filters can do a better job of catching
small airborne particles.

Compressor

The compressor motor is hermetically sealed and does not
require additional oiling.

Motors

Indoor and outdoor fan motors are permanently lubricated
and do not require additional oiling.

Clean Outside Coil (Qualified Servicer Only)

Air must be able to flow through the outdoor unit of your com-
fort system. Do not construct a fence near the unit or build a
deck or patio over the unit without first discussing your plans
with your  dealer or other qualified servicer. Restricted air-
flow could lead to poor operation and/or severe equipment
damage.

Likewise, it is important to keep the outdoor coil clean. Dirt,
leaves, or debris could also restrict the airflow. If cleaning of
the outdoor coil becomes necessary, hire a qualified servicer.
Inexperienced people could easily puncture the tubing in the
coil. Even a small hole in the tubing could eventually cause a
large loss of refrigerant. Loss of refrigerant can cause poor
operation and/or severe equipment damage.

Do not use a condensing unit cover to “protect” the outdoor
unit during the winter, unless you first discuss it with your
dealer. Any cover used must include “breathable” fabric to
avoid moisture buildup.

Check the thermostat to confirm that it is properly set.

Wait 15 minutes. Some devices in the outdoor unit or
in programmable thermostats will prevent compressor
operation for awhile, and then reset automatically. Also,
some power companies will install devices which shut
off air conditioners for several minutes on hot days. If
you wait several minutes, the unit may begin operation
on its own.

T

O

 

AVOID

 

THE

 

RISK

 

OF

 

EQUIPMENT

 

DAMAGE

 

OR

 

FIRE

INSTALL

THE

 

SAME

 

AMPERAGE

 

BREAKER

 

OR

 

FUSE

 

AS

 

YOU

 

ARE

REPLACING

.  I

F

 

THE

 

CIRCUIT

 

BREAKER

 

OR

 

FUSE

 

SHOULD

 

OPEN

AGAIN

 

WITHIN

 

THIRTY

 

DAYS

CONTACT

 

A

 

QUALIFIED

 

SERVICER

TO

 

CORRECT

 

THE

 

PROBLEM

.

I

F

 

YOU

 

REPEATEDLY

 

RESET

 

THE

 

BREAKER

 

OR

 

REPLACE

THE

 

FUSE

 

WITHOUT

 

HAVING

 

THE

 

PROBLEM

 

CORRECTED

,

YOU

 

RUN

 

THE

 

RISK

 

OF

 

SEVERE

 

EQUIPMENT

 

DAMAGE

.

B

EFORE

 C

ALLING

 Y

OUR

 S

ERVICER

Check the electrical panel  for tripped circuit breakers
or failed fuses. Reset the circuit breakers or replace
fuses as necessary.

Check the disconnect switch near the indoor furnace
or blower to confirm that it is closed.

Check for obstructions on the outdoor unit . Confirm
that it has not been covered on the sides or the top.
Remove any obstruction that can be safely  removed.
If  the unit is covered with dirt or debris, call a qualified
servicer to clean it.

Check for blockage of the indoor air inlets and outlets.
Confirm that they are open and have not been blocked
by objects (rugs, curtains or furniture).

Check the filter. If it is dirty, clean or replace it.

Listen for any unusual noise(s), other than normal op-
erating noise, that might be coming from the outdoor
unit.   If you hear unusual noise(s) coming from the
unit, call a qualified servicer.

Summary of Contents for ARPT**14 Series

























Reviews: