Amana ARPT**14 Series Installation & Operating Instructions Manual Download Page 2

2

To prevent the risk of property damage, personal 
injury, or death, do not store combustible materials or 
use gasoline or other flammable liquids or vapors in 
the vicinity of this unit.

 

 
 
 
 
 
 
 
 

 

 

 

CARBON MONOXIDE POISONING HAZARD  

-

 

 

Special Warning for Installation of Furnace or Air Handling Units in
Enclosed Areas such as Garages, Utility Rooms or Parking Areas

Carbon monoxide producing devices (such as an automobile, space
heater, gas water heater, etc.) should not be operated in enclosed areas
such as unventilated garages, utility rooms or parking areas because of
the danger of carbon monoxide (CO) poisoning resulting from the exhaust
emissions.  If a furnace or air handler is installed in an enclosed area such
as a garage, utility room or parking area and a carbon monoxide producing
device is operated therein, there must be adequate, direct outside
ventilation.

This ventilation is necessary to avoid the danger of CO poisoning which
can occur if a carbon monoxide producing device continues to operate in
the enclosed area.  Carbon monoxide emissions can be (re)circulated
throughout the structure if the furnace or air handler is operating in any
mode.

CO can cause serious illness including permanent brain damage or death.

B10259-216

2

Important Note to the Owner Regarding Product

Warranty

Your warranty certificate is supplied as a separate document
with the unit installed by your contractor. Read the limited
warranty certificate carefully to determine what is and is not
covered and keep the warranty certificate in a safe place. If
you are unable to locate the warranty certificate please con-
tact your installing contractor or contact customer service (877-
254-4729) to obtain a copy.

IMPORTANT: 

To receive the 10 Year Parts Limited Warranty,

online registration must be completed within 60 days of in-
stallation. Online registration is not required in California or
Quebec. Complete warranty details are available from your
local dealer or, for Goodman® brand products, visit
www.goodmanmfg.com and for Amana® brand product, visit
www.amana-hac.com.

IMPORTANT: 

To register your Goodman

®

 brand unit, go to

www.goodmanmfg.com and click “Warranty Registration”.
Complete registration as prompted.

HIGH VOLTAGE!

 

Failure to do so may cause property damage,
personal injury or death.

Disconnect ALL power before servicing.
Multiple power sources may be present.

Installation and repair of this unit should be performed

by individuals meeting the requirements of an

“entry level technician”

 as specified by 

the Air-Conditioning, Heating and Refrigeration Institute
(AHRI).  Attempting to install or repair this unit without
such background may result in product damage, 
personal injury or death.

ONLY 

, at a  minimum,

This product is factory-shipped for use with 
208/240/1/60 electrical power supply. 
reconfigure this air handler to operate with any other 
power supply.

DO NOT 

To avoid property damage, personal injury or death 
due to electrical shock, this unit MUST have an 

 electrical ground. The 

electrical ground circuit may consist of an 
appropriately sized electrical wire connecting the 
ground lug in the unit control box to the building 
electrical service panel.
Other methods of grounding are permitted if performed 
in accordance with the National Electric Code 
(NEC)/American National Standards Institute 
(ANSI)/National Fire Protection Association (NFPA) 70 
and local/state codes. In Canada, electrical grounding 
is to be in accordance with the Canadian Electric Code  
(CSA) C22.1.

uninterrupted, unbroken

When installing or servicing this equipment, safety 
clothing, including hand and eye protection, is 
strongly recommended.  If installing in an area that has 
special safety requirements (hard hats, etc.),  bserve 
these requirements.

o

Do not connect to or use any device that is not design-
certified by Goodman for use with this unit. Serious 
property damage, personal injury, reduced unit 
performance and/or hazardous conditions may result 
from the use of such non-approved devices.

 

is a registered trademark of Maytag Corporation or its related companies and is used under

license to Goodman Company, L.P., Houston, TX.  All rights reserved.

Summary of Contents for ARPT**14 Series

























Reviews: