AM.PM joy F8540000, Manual

Page: 3 / 13

4 5
Operating interval of pressure in water
supply network 0,5–6,0 Atm. (50–620 kPa).
Recommended pressure interval in water
supply network 2,0–5,0 Atm (206–515 kPa).
Difference of cold and hot water pressure
may come up to ± 10%. In case of deviation
of water supply system pressure parameters
to the specified values installation of devices
for pressure increase / reduction is required.
Water temperature hot water supply network
is ≤80 ° С. Recommended temperature of
water in cold water supply network is 20 ° С,
in hot water supply network 60 ° С.
To avoid mechanical (abrasive) particles
penetration inside the product it is
compulsorily required to install filters of
100–300 mc.
mIxer InstallatIon
1. Disconnect hot and cold water supply.
Screw in eccentric connectors (2) into
water supply pipes outlets having sealed
the thread part preliminary with sealer. Find
position for eccentric connectors for them
to coincide and be adjusted to the mixer
connecting position (1), herewith mixer
position should be horizontal.
attention! Before mixer installation check
correctness of connections in water supply
network: hot water connection should be
taken out from the left side and cold water
connection should be taken out from the
left side of the product housing. During
mixer installation with gas water heater it is
necessary to know the parameters of water
output pressure of the heater. In case of
variation of pressure between cold and hot
water more than 1 Atm. (103 kPa) there is a
possibility of noise in the thermostat.
attention! The manufacturer reserves the
right of making changes into mixer design
without preliminary notification.
2. Switch on hot and cold water supply for
short period of time. Make sure that there
are no mechanical particles and afterwards
disconnect water supply (do not forget to
provide safe water discharge into sewerage
system).
temperature adjustment:
As depending on pressure and temperature
of water supply system actual temperature
value fixed by safety button may deviate
from preset 38
° С, after mixer installation its
adjustment is required. For that:
The hot water
connector
The cold water
connector
2
1
3. Install decorative plates (4) onto the
eccentric connectors (2), place filtering
elements (3) inside mixer housing (1) and
by means of tools with soft cover plates (to
avoid damage of mixer decorative cover),
connect mixer housing.
2 4 3
1
4. Switch on water supply system. During
mixer closed position check leakproofness of
all connections. If required arrange additional
tightening and sealing of connections
(having closed water supply preliminary).
5. Connect shower kit.
1 2 3
5
4
6
1. remove protective cap (5),
2. unscrew fitting bolt (4) remove handle
(3), decorative indicator ring (2) and fixing
ring (1)
3. switch on water flow by means of flow
adjustment handle
4. by turning thermal cartridge stock (6) to
the required side (temperature increase/
decrease), find position when water
temperature at the outlet comprises 38С
(use the thermometer (not included into the
delivery set)).
5. switch on water flow
6. make assembly (item.2) in reverse order.
mIxer operatIon
There is a safety button on thermostat handle
(right) that prevents water temperature
increase above 38 ° С. For water temperature
increase at the mixer outlet push the button
and keep turning thermostat handle to
increase water temperature.
maIntenance recommendatIons
Risk of breaking of mixer cartridge may be
significantly reduced by means of installation
of filters 100-300 mk to the mixer pipes that
prevent penetration of foreign particles (rust,
sand, etc.) to the mixer.
To avoid lime spots at the mixer housing
the mixer is recommended to be regularly
cleaned. Mixer cleaning should be carried
out by soap solution with the following rinse
with water and removing moisture by dry
soft cloth.
The remainings of liquid soap, shower gel
may also cause damages of decorative
cover. In case of their penetration onto
the mixer housing it should be thoroughly
cleaned with clean water
To avoid damages of product surface it
is forbidden to use abrasive для ухода
solutions and pastes.
To avoid changes color of decorative cover
it is forbidden to use chemicals for cleaning
that contain aggressive chemical substances
of acids, alkali, ammonium chloride and
other components containing chlorine.
Periodical cleaning of filtering elements
located at the inlet nozzles of mixer is
recommended (at least once a year). For
this purpose:
– switch off cold and hot water supply
system
– by means of the tool with soft cover plates
(to avoid damage of decorative cover of
mixer nuts) disconnect mixer housing from
eccentric connectors
– remove filtering elements, clean them and
install again.
– install mixer housing in accordance with
item 3–4 of Installation instructions.