Alware Lensman-Pro 3 Axis Instruction Manual Download Page 7 | Manualshive

Page: 7 / 23

background image

STEP 2: Gimbal Assembly

Put the Main Body Assembly as shown.

Take off four Mounting Screws.

Release the Upper Handle of the Handle Unit.

Insert the Main Cable through the hole.

Secure the Handle Unit to the Yaw Motor

with 4pcs Screws.

Plug the 5-wires Cable to the Joystick.

7

«
...
5
6
7
8
9
...
»

Summary of Contents for Lensman-Pro 3 Axis
























Reviews:

No comments

Related manuals for Lensman-Pro 3 Axis

Brand: LAZER Pages: 13

Brand: Latento Pages: 60

Brand: Easy Quick Pages: 11

Brand: Radio Shack Pages: 2

Brand: Keating Of Chicago Pages: 2

Brand: LaserTrack Pages: 12

Brand: GÄN Pages: 24

Bicycle Accessories

Brand: Baby Jogger Pages: 20

Brand: Echo Pages: 4

Brand: PAJ Pages: 95

Brand: Labona Pages: 12

5500DN - Phaser B/W Laser Printer

Brand: Xerox Pages: 2

3600B - Phaser B/W Laser Printer

Brand: Xerox Pages: 2

Brand: Digisol Pages: 25

Brand: R&G Pages: 22

Brand: R&G Pages: 8

KARLSUDD TRAVEL BED

Brand: Carena Pages: 8

Brand: PROAIM Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands