background image

INSTALLATION AND OPERATION MANUAL | CUL11 CONTROL UNIT

13

13

COMMISSIONING CERTIFICATE

10.  COMMISSIONING CERTIFICATE

Serial number and date of manufacture _____________________________________________

 

data from the product label

Information about organisation authorised to perform installation and technical maintenance

 ______________________________________________________________________________
 ______________________________________________________________________________

name, address and phone

 

Date of installation: ________________________________________

 

L.S.

 

 

 

day, month, year

 

Signature of the person

 

responsible for the installation _______________________________

 signature 

 

 ________________________________________________________

print name 

Consumer (Customer) has verified the completion, agreed and accepted warranty conditions 

and terms and has no claims against the product appearance. The product is installed and ad-

justed in accordance with the established requirements and qualified for operation. Consumer 

has been provided with information on existing hazards and risks, as well as rules on operation.
Information about customer (consumer) ____________________________________________

 ______________________________________________________________________________

name, address and phone

 

Signature of customer (consumer) _____________________

                                                               signature

 

 

  _________________________________________________

print name 

Summary of Contents for CUL11





















Reviews: