Altronix AL1002ULADAJ, Installation Manual

Page: 2 / 16

- 2 - AL1002ULADAJ
Overview:
Altronix AL1002ULADAJ is an extremely cost-effective 10A remote power supply/battery charger. It may be
connected to any 12 or 24 volt Fire Alarm Control Panel (FACP). Primary applications include Notification
Appliance Circuit (NAC such as strobes and horns) expansion support to meet ADA requirements. It also pro-
vides auxiliary power to support system accessories. The unit delivers electronically regulated and filtered 24
volt power to Class B, Style W, Y or Class A, Style Z NAC loop circuits. Additionally, a separate 1.0A auxiliary
output for four (4)-wire smoke detectors is available. The 10A max. alarm current can be divided between the
four (4) outputs for powering NAC devices. Each output is rated at 2.5A max., and can be independently pro-
grammed for Steady, Temporal Code 3 or Strobe Synchronization. All outputs may be programmed for Input to
Output Follower Mode (output will follow input). In non-alarm condition independent loop supervision for Class
A, Style Z and/or Class B, Style W, Y FACP NAC circuits is provided. In the event of a loop trouble, the FACP
will be notified via the steered input (Input 1 or Input 2). In addition, there are common trouble output terminals
(NC, C, NO) which are used to indicate general loop/system trouble. A common trouble input is provided for
optional NC (normally closed) devices to report trouble to the FACP. Two (2) FACP signaling outputs can be
employed and directed to control supervision and power delivery to any combination of the four (4) outputs.
Note: The information in this document is valid for models AL1002ULADAJ and AL1002UL2ADAJ.
Model AL1002ULADAJ is equivalent to model AL1002UL2ADAJ.
Specifications:
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture.
This installation should be made by qualified service personnel and should conform to all local codes.
Agency Listings:
• UL Listed Control Units for Fire Protective
Signaling Systems (UL 864).
• MEA - NYC Department of Buildings Approved.
• CSFM - California State Fire Marshal Approved.
• FM - Factory Mutual Approved.
• NFPA 72 Compliant.
Input:
• Power input 120VAC 60Hz, 5.0A.
• Two (2) Class A, Style Z or two (2) Class B,
Style W, Y FACP inputs.
• Two (2) NC dry contact trigger inputs.
Output:
• Class 2 Rated power-limited outputs.
• 24VDC @10A max total alarm current.
• 2.5A max current per output.
• Separate 1.0A auxiliary output.
• Programmable supervised indicating circuit outputs:
Four (4) Class B, Style W, Y or Two (2) Class A,
Style Z or One (1) Class A, Style Z and Two (2)
Class B, Style W, Y (see Application Guide).
• Thermal and short circuit protection with auto reset.
Battery Backup:
• Built-in charger for sealed lead acid or gel type
batteries.
• Automatic switchover to stand-by battery when
AC Fails.
• Zero voltage drop when switching over to
battery backup.
Supervision:
• AC fail supervision (form “C” contact, 1A/28VDC).
Factory set for 2 hours with optional 1 minute
delay setting (field selectable).
• Instant local AC trouble reporting relay
(form “C” contact, 1A / 28VDC).
• Battery presence and low battery supervision
(form “C” contact, 1A / 28VDC).
Visual Indicators:
• Input and output status LED indicators.
Special Features:
• 2-wire horn/strobe Sync mode allows audible
notification appliances (horns) to be silenced
while visual notification appliances (strobes)
continue to operate.
• Sync protocols include Potter/Amseco, Faraday,
Gentex
®
, System Sensor
®
, and CooperWheelock
®
.
• Temporal Code 3, Steady Mode, Input to Output
Follower Mode (maintains synchronization of
notification appliances circuit).
• Compatible with 12VDC or 24VDC fire panels.
• Output loop supervision steered to Input 1 or Input 2.
• Signal circuit trouble memory (helps identify
intermittent loop problems).
• Common trouble input and output.
• Ground fault detection.
• Unit includes power supply, red enclosure,
cam lock, and battery leads.
Enclosure Dimensions
(approx. H x W x D)
:
18” x 14.5” x 4.5”
(457.2mm x 368.3mm x 114.3mm).