background image

3

3. CONTROL ELEMENTS

SP

OT

LIG

HT

3. CONTROL ELEMENTS

Rear Panel:

Two types of input connectors are provided for input connections: 2 x female 
locking XLR type connectors, and 2 x 1/4" TRS jack connectors (tip-ring-sleeve). 
The maximum input level that the processor can accept is +20 dBu 
(ref.: 0.775Vrms).

This button allows you to select between 4 dBu or -10 dBv nominal 
operating level.

This switch locks/unlocks all access to the front panel of the TERMINATOR II.

7 AC Inlet and Fuse holder 

9 Input/Output Connectors

10 Operating Level Switch

11 Lock Switch

                   AC INPUT

100-120V

/220-240V

60-50Hz 

    Rated Power Consumption 20W

FUSE:

220-240V: T315mAL 250VAC
100-120V: T500mAL 250VAC
REPLACE FUSE WITH CORRECT  

  TYPE ONLY 

Apparaten skall anslutas till
jordat uttag nar den ansluts
till ett natverk

OUTPUTS

CHANNEL 2

INPUTS

LOCK

ON              OFF

+4 dBU
-10 dBV

TIP/PIN 2
RING/PIN 3
SLEEVE/PIN 1

TIP/PIN 2
RING/PIN 3
SLEEVE/PIN 1

OUTPUTS

CHANNEL 1

INPUTS

+4 dBU
-10 dBV

TIP/PIN 2
RING/PIN 3
SLEEVE/PIN 1

TIP/PIN 2
RING/PIN 3
SLEEVE/PIN 1

VOLTAGE SELECTOR

~100-120 
      VAC

~220-240 
      VAC

7

8

9

11

10

8 Voltage Selector

This switch has two choices for voltage, 100-120 VAC or 220-240 VAC.

Standard IEC receptacle. Connect your TERMINATOR II to the AC Inlet with 
the supplied AC power cord. Before powering up your TERMINATOR II for the 
firs t ti me,  make certain the stated power requirement of the unit matches the 
voltage supplied by the AC socket.

If the fuse blows, replaced with a fuse of the correct type only. 

8

Insert on the SUB GROUP/MAIN L-R of the Mixer

1- Connect the TRS (tip-ring-sleeve) stereo jack into the Mixer SUB GROUP/ 
    MAIN L-R, Insert socket.

2- C onne ct t he S end  stereo jack (unbalanced) to the CH1 Input of TERMINATOR II 
    and the C H1 Output of TERMINATOR II with a Return stereo jack (unbalanced). 

3- Set the sensitivity at -10 dBu on the TERMINATOR II and adjust the SUB 
    GROUP/ MAIN L-R, fader control on the MIXER for having a necessary level 
    on TERMINATOR II. 

 For maximum performance and proper operation,  the average input signal should 

consistently light up at the 0 dBu LED  and the +10 dBu  LED lighting occasionally.

3. CONTROL ELEMENTS

5. INSTALLATION AND CONNECTION 

INSERT SUB 2

INSERT SUB 1

S

E

N

D

 

S

E

N

D

 

R

E

TU

R

N

R

E

TU

R

N

OFF

POWER

ON

INPUT LEVEL dBu

CLIP

+18

+10

0

-10

AUTOMATIC

FEEDBACK

KILLER

TERMINATOR II

CHANNEL 1

CHANNEL 2

BYPASS

LIVE MODE VARIATIONS 

 1      2     3     4     5     6     7     8    9    10  11   12  13   14   15  16  17  18  19  20  21  22  23     24  

MUSIC

SPEECH

MUSIC

SPEECH

FILTERS

1/40

 CH 1

1/5

1/80

1/40

 CH 2

1/5

1/80

 CH 1

 CH 2

Summary of Contents for TERMINATOR II









Reviews: