Altherma EKHBHE008AA3V3, Operation Manual

Page: 11 / 20

EKHBH/XE008AA3V3
Indoor unit for air to water heat pump system and options
4PW48442-1B
Operation manual
10
Consulting domestic water heating, booster heater or quiet
mode
Consulting domestic water heating, booster heater or quiet mode is
carried out as follows.
1 Press the < button.
The actual mode is blinking.
2 Use the
pi
and
pj
buttons to select the mode you want
to consult (quiet mode s , booster heating m or domestic
water heating w ).
The selected mode is blinking.
3 Press the < button to confirm the selected mode.
The first programmed action is displayed.
4 Use the
pi
and
pj
buttons to consult the programmed
actions.
This is called the readout mode. Empty program actions (e.g. 4
and 5) are not displayed.
By pressing the
pr
button several times, you return to previous
steps in this procedure and finally return to normal operation.
Tips and tricks
Programming the next day(s)
After confirming the programmed actions of a specific day (i.e. after
pressing the
< button for 5 seconds), press the pr button once. You
can now select another day by using the pi and pj buttons
and restart consulting and programming.
Copying programmed actions to next day
In heating/cooling program it is possible to copy all programmed
actions of a specific day to the next day (e.g. copy all programmed
actions from "
1 " to " 2 ").
To copy programmed actions to the next day, proceed as follows:
1 Press the
<
button.
The actual mode is blinking.
2 Use the pi and pj buttons to select the mode you want
to program.
The selected mode is blinking.
You can leave programming by pressing the pr button.
3 Press the < button to confirm the selected mode.
The actual day is blinking.
4 Select the day you would like to copy to the next day by means
of the
pi
and
pj
buttons.
The selected day is blinking.
You can return to step 2 by pressing the
pr
button.
5 Press the
<
and
pr
buttons simultaneously for 5 seconds.
After 5 seconds the display will show the next day (e.g. " 2 " if
" 1 " was selected first). This indicates that the day has been
copied.
You can return to step 2 by pressing the
pr
button.
Deleting one or more programmed actions
Deleting one or more programmed actions is done at the same time
as storing the programmed actions.
When all actions for one day have been programmed, make sure that
the display shows the highest action number you would like to save.
By pressing the
< button for 5 seconds, you store all actions except
those with a higher action number than the one that is displayed.
E.g. when the
<
button is pressed when action number 3 is
displayed, actions 1, 2 and 3 are stored but 4 and 5 are deleted.
Deleting a mode
1 Press the
<
button.
The actual mode is blinking.
2 Use the pi and pj buttons to select the mode you want
to delete (quiet mode s , booster heating m or domestic water
heating w ).
The selected mode is blinking.
3 Press the
<
and
ba
button simultaneously for 5 seconds to
delete the selected mode.
Deleting a day of the week (cooling or heating mode)
1 Use the = button to select the operation mode (cooling or
heating) you want to delete.
2 Press the < button.
The actual mode is blinking.
3 Press the
<
button to confirm the selected mode.
The actual day is blinking.
4 Select the day you would like to delete by means of the pi
and pj buttons.
The selected day is blinking.
5 Press the
<
and
ba
button simultaneously for 5 seconds to
delete the selected day.
O
PERATING THE REMOTE ALARM OPTION
The optional EKRP1HB remote alarm address card can be used to
remotely monitor your system. This address card offers 2 voltage free
outputs.
■
Output 1 = alarm output: this output will be enabled when your
unit is in error condition in case of default setting of field setting
parameter [C-01].
Refer to "[C] Solar priority mode" on page 14 for other
possibilities.
■
Output 2 = ON/OFF output: this output will be enabled when
your unit is in ON condition.
For more details about the wiring connections of this option, refer to
the wiring diagram of the unit.
NOTE
Returning to previous steps in this procedure is done
by pressing the
pr button.