Altera Arria V GZ User Manual Download

Page: 131 / 300

Chapter 6: IP Core Interfaces

6–37

Transaction Layer Configuration Space Signals

November 2012

Altera Corporation

Arria V GZ Hard IP for PCI Express

User Guide

Configuration Space Register Access Timing

Figure 6–33

shows typical traffic on the

tl_cfg_ctl

bus. The

tl_cfg_add

index

increments on the rising edge of

pld_clk

specifying which Configuration Space

tl_cfg_ctl

[30]

Link Status 2 Register[0]

Current de-emphasis level.

[29:25]

Status Register[15:11]

Records the following 5 primary command status errors:

■

Bit 15: detected parity error

■

Bit 14: signaled system error

■

Bit 13: received master abort

■

Bit 12: received target abort

■

Bit 11: signalled target abort

[24]

Secondary Status Register[8]

Master data parity error

[23:6]

Root Status Register[17:0]

Records the following PME status information:

■

Bit 17: PME pending

■

Bit 16: PME status

■

Bits[15:0]: PME request ID[15:0]

[5:1]

Secondary Status Register[15:11]

Records the following 5 secondary command status errors:

■

Bit 15: detected parity error

■

Bit 14: received system error

■

Bit 13: received master abort

■

Bit 12: received target abort

■

Bit 11: signalled target abort

[0]

Secondary Status Register[8]

Master Data Parity Error

Table 6–14. Mapping Between tl_cfg_sts and Configuration Space Registers (Part 2 of 2)

tl_cfg_sts

Configuration Space Register

Description

Figure 6–33. tl_cfg_ctl Timing

pld_clk

tl_cfg_add[3:0]

tl_cfg_ctl[31:0]

00...

7F...

00000000

00...

Summary of Contents for Arria V GZ













































































































































































































































































































Search results

Summary of Contents for Arria V GZ

Reviews:

Related manuals for Arria V GZ

Brands by name

Popular brands

Altera Arria V GZ, User Manual

Search results

Summary of Contents for Arria V GZ

Reviews:

Related manuals for Arria V GZ

Brands by name

Popular brands